Main blade nit picky question
-
When I first got my new Super Tinker, I noticed that it had 3 tiny little nicks on the very tip of the main blade. They seemed pretty uniform, and so I thought they may have been a manufacturing defect, I figured no problem I'll just take care of them with some quality time on the whet stones. This evening I went to do some maintenance on the Super Tinker, and I realized that the exact same 3 little nicks are back again! I know I could just sharpen the blade again and take care of them, but now I'm wondering what is causing them. Could this be that the blade is contacting the liner when closed? Does anyone else have this problem? It's not a big deal, but I spend a lot of time tuning up my knife so that it is shaving sharp & I hate to see stuff like this happening.
Sent from my iPad using Tapatalk
-
Get some pic's if you can, it might be easier to figure out if we can see what is going on.
I'm sure someone will be able to help.
-

Perhaps, if you let snap the blade (closing) it hit the spring or the liner?
Pics will help.regards
Markus
-
Don't know for sure but I will say every single one of the 84/91/93mm knives that I have had the blade would hit the liner if I let it snap shut. So when I carry a 111mm, I relish letting it snap shut lol.
-
The liners are softer than steel so they 'should' deform before nicking a blade. I have older alox with contact lines you can see in the liner where the blade hit it over time and made a groove.
-
Sounds like the blade is hitting a piece of something steel when it snaps closed. The shoulder at the tang should prevent the blade from hitting the filler (the little spacer there between the small-blade tang and the divider) - and both divider and filler are softer than the blade anyway. Can you see a tiny coil of something hard stuck to the filler?
-
It's actually a common problem on Bantams and Waiters, not so much on bigger knives. And while steel (knife) is stronger than the liners, the sharpened thin edge is not and chips cause of it.
-
Thanks for the feedback guys, I think it must be hitting the liner when it snaps shut. I looked and found similar nicks on my Tinker as well. The liner looks fine, and there doesn't seem to be anything abnormal there. I tried to take a picture of the nicks , and quite frankly they are so small it was almost impossible to get a picture. Anyhow , here's the picture, hopefully it gives you all an idea of what's going on:

-
I just checked out my SI and CT41 and both have marks on the liner where the tip hits from snapping shut.
The CT41 actually has two. The second one is curved because for a while the tip was bent from dropping it.
However there is no damage to the blade. And if there was I would expect it to roll or flatten the edge not chip it.
You could try to stone the edge back a mm or so to give it some more clearance, having a little more belly won't hurt.
-
@zoidberg said:
I just checked out my SI and CT41 and both have marks on the liner where the tip hits from snapping shut.The CT41 actually has two. The second one is curved because for a while the tip was bent from dropping it.
However there is no damage to the blade. And if there was I would expect it to roll or flatten the edge not chip it.
You could try to stone the edge back a mm or so to give it some more clearance, having a little more belly won't hurt.
Thanks so much for taking the time to look at your own SAKs, it is good to hear that liner contact is not uncommon (even if mine seems to be affecting the blade in a strange manner). I'm going to try to ignore the nicks for the time being, and then over time as the blade gets sharpened it will hopefully stop contacting the liner. I'm trying not too be too picky about this, since it is my EDC blade and it's only going to acquire more bumps and bruises along the way!
Thanks,
-gccSent from my iPad using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
