Rebar Problem
-
My Rebar has a problem, when I cut something with the wire cutters that take a relative amount of force or if I just squeeze down on the handles really tight the pliers seem to tighten up and I either have to open and close the tool to get it loose or while open, sort of pull of like pull one of the handles toward me and push the other away to get them loose again. It's really annoying when you have multiple cutting to do and the pliers become stiff like that. I hope that makes sense otherwise its an awesome tool.
Here is a link to a vid on youtube with the same problem.
https://www.youtube.com/watch?v=ZBoqoGbsF5UShould I send it back or is their anything I could try to stop this from happening?
I have tried lubricant spray and oil but no luck so far.
-
Hey, Mr. Mustard. Until you get a better answer, my first thought is that these suckers loosen up over time with usage. So if you can deal with it for a while, I bet that it will be self-correcting. But I have never had first hand experience with this issue, so maybe someone else can provide some insight. Good luck.
-
Try opening and closing them a bunch of times.
if that doesn't work.
send it back to leatherman . I don't know if they will cover them though.
or
remove the cutters and try fix them yourself. Lay them on a flat stone and remove the burr .
or
order a new set of cutters. They sell a replacement
-
I had a problem with one of my Rebars where the replaceable cutters were putting pressure on the pliers causing them to stick shut. After opening and closing them about 500 times, this problem went away. It was obvious what the problem was and I didn't see a point to sending it in for repair.
I hope this is all that your problem is. Give it a try and let us know

-
That was a problem and video posted by a member here.
Thread for reference:
-
@mrmustard said:
My Rebar has a problem ... or if I just squeeze down on the handles really tight the pliers seem to tighten upThere is a lot being made of squeezing hard to produce the problem but during your vid when you were just flicking the handles together it stuck once but you just moved on. Can that be replicated because that is what is significant?
All the areas which can bind are visible except for the pivot surface. My Rebar doesn't exhibit this problem but I can see very slight eccentricity in the pivot. To me this is another "tolerance build-up" issue like Rebar jaws jamming when closing with awl deployed (and Juice jaws jamming when closing-up).
LM's previous specific response to this identical problem which I paraphrase as "we don't consider pulling tiny splinters out of your finger a valid use" is disappointing but not surprising. This just illustrates that manufacturers (LM even) don't like admitting design or QC failure because it creates a precedent. What you needed to do was "break" your Rebar (legitimately) and then the legendary warranty service would probably have kicked in.
-
There's an easy way to troubleshoot where it's binding on the Rebar: Run one of the wire cutter bits out and open and close the jaws. If the problem goes away, it's the cutter jaws dragging.
My Wave and Skeletool did that with their fixed cutters, it just took wearing them in.
-
The Rebar is around 6-7months old and has seen a fair bit of use but thanks for the suggestions guys, will give it a try!! Back to the old lube and watching classic movies while opening and closing MT's to get them loose. ::)
P.S. I hope that everyone did not get the wrong impression of the Youtube video being my own, I just posted that as a reference because our problem is the same

If all does not go well I will send the tool over to LM in South Africa and will give feedback on their service.
@enki_ck said:
That was a problem and video posted by a member here.Thread for reference:
-
@mrmustard said:
P.S. I hope that everyone did not get the wrong impression of the Youtube video being my own, I just posted that as a reference because our problem is the same
Whoops. I followed enki_ck's link and lost it

-
Mine does these too, but not when using the cutters. If you squeeze the pliers (even when empty), the plier pivot becomes noticeably stiffer until I close and open the tool again.
-
I had this problem with one of my Rebars. Really annoying and nothing to do with the cutters, it's just down to the pivot.
Over time it's sorted itself out though and isn't a problem any more.
-
That was my video.
After a month of WD40, 3in1 oil and even vaseline. Using it for work and hobby every day almost nothing changed. If your plier head is tight all the time the friction will have a chance to grind the sticking surfaces away. But if it only jams in one position they will stay this way...
And the problem persist even without the cutters.I have sent my rebar to leatherman uk (without the cutters to make a point) and they returned it saying they can't see a problem. So I have send it again with a link to this video. Yet again I got it back telling me it's up to specs (read the caption at the end of the video).
So I contacted leatherman US with above link (by that time the video made a bit of a stink on line and on this forum) and I got a reply that "there is nothing wrong with it but they will replace it for me as a good will gesture"... It wasn't very cost effective for me to do that (postage would be like 20-30% of the tool value and at least 3 weeks) so I dropped the whole situation.Now I am a heavy user and a big fan of Leatherman tools. Over the last decade I have used almost all of them so I think I know how a MT should behave. I have also used and even abused Leatherman warranty on numerous occasions for myself and my friends and they always came thru singing without a glitch.
I really couldn't believe the resistance I got from them this time (many emails...) when it was a genuine fault in a tool... -
Hey BigMatt. Thanks for your video. Sorry if I used it without permission
It was really bugging me because I also own quite a number of LM tools and none of the others have shown this type of irregularity and your video was the only one that had it pinned down to the nail so that's why I used it as a reference.
I have never ever used LM's warranty so it will be a good trial run for me anyway.
-
No problem mate.
Good to see I'm not the only one and I'm not going crazy...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login