Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Have a basic question about a bent blade

Scheduled Pinned Locked Moved General Tool Discussion
8 Posts 1 Posters 1.4k Views
  1. Home
  2. Tool Talk
  3. General Tool Discussion
  4. Have a basic question about a bent blade
Have a basic question about a bent blade
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • mikekoz Offline
    mikekoz
    Posts: 637
    mikekoz Offline
    mikekoz
    wrote on last edited by
    Quote Reply

      I just got a new multitool, and the very tip of the blade is slightly bent. It was only about $17.00, and it would probably not be worthwhile or cost effective to return it to the vendor. I was going to try to straighten it using a set of pliers. Will this work, or will I just break the tip off? The blade is made out of 3cr13 steel if that helps anybody. This defect probably would have no effect on the usability of the blade, but it is bothering me nevertheless!!! Thanks to anybody that can give me any advice!

      1 Reply Last reply
      • AimlessWanderer Offline
        AimlessWanderer
        Posts: 17,518
        AimlessWanderer Offline
        AimlessWanderer
        wrote on last edited by
        #1 Quote Reply

          If it doesn't break, it will probably still weaken it - plus there's a good chance you'll not properly realign it again anyway. It it breaks, you'll need to regrind the tip ... so why not do that first and save yourself some intermediate agro ... or it it's not hurting function, live with it as it is

          The cantankerous but occasionally useful member, formally known as 50ft-trad

          1 Reply Last reply
          • MultiMat Offline
            MultiMat
            Posts: 8,694
            MultiMat Offline
            MultiMat
            wrote on last edited by
            #2 Quote Reply

              I have had some luck with bent blade tips, I try putting the blade in a vice , if it is really badly bent this helps straighten it a bit. I then place the blade on a perfectly flat surface & try tapping the bend out with a very small hammer , flipping the blade over & tapping each side.

              But like Al said above there is a good chance you will have a weakened blade tip , I think I have broken 2 blade tips trying to straighten them, one was a LM Mini that I had gotten 95% straight :facepalm:(could not just leave it be :( :() & a Aussie Army Swisstool , I used a too big hammer on it :facepalm: :facepalm: :facepalm:

              I think the pros heat the blade up , straighten it & then re-temper the blade :think: :think:


              "Downunder Mod (that sounds dirty, doesn't it?)"
              Yeh Baby :P >:D >:D

              1 Reply Last reply
              • jzmtl Offline
                jzmtl
                Posts: 8,551
                jzmtl Offline
                jzmtl
                wrote on last edited by
                #3 Quote Reply

                  I would just take pliers to it, since as you said it's not worth it to exchange another, the worst can happen is it breaks and you regrind the tip.

                  1 Reply Last reply
                  • Aloha Offline
                    Aloha
                    Global Moderators
                    Posts: 31,235
                    Aloha Offline
                    Aloha
                    Global Moderators
                    wrote on last edited by
                    #4 Quote Reply

                      I have a SAK that has a bent blade and I've just let it be. While it sucks it would suck even more broken. I understand this is not advice on how to "fix" it but sometimes the best thing to do is, nothing. Good luck.

                      Esse Quam Videri

                      Merit Badges
                      One Piece Collector Japanese PST Juice Collector Level 1 Reviewer Camping Fire Making Flashlight Outdoor Cook BO Tools Level 3 Santa Traditional Folder Challenge Pen Challenge
                      1 Reply Last reply
                      • mikekoz Offline
                        mikekoz
                        Posts: 637
                        mikekoz Offline
                        mikekoz
                        wrote on last edited by
                        #5 Quote Reply

                          Thanks everybody! I emailed Amazon to see if they would do an exchange without me having to pay return postage (unlikely!). The thing to do though, as some of you have stated, is to just leave it be and live with it. I was not expecting a whole lot from it anyway, but it still looks like a great deal for the dollar!

                          1 Reply Last reply
                          • CanadianLMfan Offline
                            CanadianLMfan
                            Posts: 3,334
                            CanadianLMfan Offline
                            CanadianLMfan
                            wrote on last edited by
                            #6 Quote Reply

                              $17, 3cr13 steel, it was a Gerber Dime, wasn't it? :whistle:

                              Leatherman

                              1 Reply Last reply
                              • mikekoz Offline
                                mikekoz
                                Posts: 637
                                mikekoz Offline
                                mikekoz
                                wrote on last edited by
                                #7 Quote Reply

                                  @CanadianLMfan said:
                                  $17, 3cr13 steel, it was a Gerber Dime, wasn't it? :whistle:

                                   Actually, it is a full sized multitool made by Valtev. Amazon actually is offering me 40% back on it because of the defect, and I am going to take them up  on it. This is one of the few inexpensive multitools I have bought where all of the tools lock! It is no Leatherman, but for the price seems very solid!
                                  
                                  1 Reply Last reply

                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                  With your input, this post could be even better 💗

                                  Register Login

                                  1. Home
                                  2. Tool Talk
                                  3. General Tool Discussion
                                  4. Have a basic question about a bent blade
                                  Reply
                                  • Reply as topic
                                  Log in to reply
                                  COMMUNITY LINKS
                                  EDC-TV SAKWiki GearFeed SAKSelector
                                  Operational Funds

                                  Help us keep the Unworkable working!

                                  Make A Donation
                                  November Goal: $300.00
                                  Due Date: Nov 30
                                  Total Receipts: $0.00
                                  Below Goal: $300.00
                                  0% funded
                                  • Login

                                  • Don't have an account? Register

                                  • Login or register to search.
                                  • First post
                                    Last post
                                  0