Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Sharpening angle

Scheduled Pinned Locked Moved Swiss Army Knights Forum
11 Posts 1 Posters 8.4k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Sharpening angle
Sharpening angle
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Philby Offline
    Philby
    Posts: 851
    Philby Offline
    Philby
    wrote on last edited by
    #1 Quote Reply

      I sharpen my knives by hand, following the bezel. If the bezel is gone to far, I hold the knife at 90 degrees, then reduce by a third to 30, half this to 15, then add a few more degrees. I feel 20 will give a less fine edge but be more resilient. Depends what you use it for, chefs knives tend to have a finer edge for slicing. I think 15 is too fine for a pocket knife. I think Victorinox recommend 15-20. If the only settings you have are 15 or 20, I would go with 20. Try it out on old beater knives first to test. Let us know how you get on. :tu:

      1 Reply Last reply
      • Sorel Offline
        Sorel
        Posts: 28
        Sorel Offline
        Sorel
        wrote on last edited by
        #2 Quote Reply

          I use a Sharpmaker specifically in order to not have to think about angles. I use the 20 on all my knives, works great. A few minutes with the Sharpmaker recently put an edge on my brand-new Minichamp that somehow seemed even sharper than factory. I don't know if that's even possible or if I'm somehow deluding myself, but either way, the Sharpmaker's 20 setting works beautifully.

          1 Reply Last reply
          • neillcurrie Offline
            neillcurrie
            Posts: 860
            neillcurrie Offline
            neillcurrie
            wrote on last edited by
            #3 Quote Reply

              I use a Lansky 5 stone system, though I often don't use the rougher stone(s), as required. I always use 25 degrees, and even convert chisel ground blades (LM Squirts, for example) to the same 25 degree total edge, but ground both sides now. The only edges I leave as chisel-ground, are where the flat edge buts cleanly up against another flat edge as edge/person protection......think CRKT "peck".
              Afterwards I strop with about 12 to 15 inches of an old leather belt stuck to a piece of solid particle board. Leaves a wicked sharp edge.
              Since I baby the blades afterwards, and don't put a nick in them hardly ever, all they need is an occasional stropping.

              1 Reply Last reply
              • Humppa Offline
                Humppa
                Posts: 963
                Humppa Offline
                Humppa
                wrote on last edited by
                #4 Quote Reply

                  I use the Spydie Sharpie on occasion. I use to sharpen my blades freehand.

                  But when it needs to get a little faster, I like the sharpie. Always use the 20 degree angle on this system. Never used the 15 degree. It works great and I realised, that this is quite the perfect angle for my blades. I really like the way the hold the edge and do not tend to chip or break out in any way.

                  1 Reply Last reply
                  • Mextreme Offline
                    Mextreme
                    Posts: 454
                    Mextreme Offline
                    Mextreme
                    wrote on last edited by
                    #5 Quote Reply

                      Thank you guys!

                      Took your advice and put a nice 20 degree angle an all of them and now they are REALLY sharp and I'm sure it's the right choice.

                      1 Reply Last reply
                      • Philby Offline
                        Philby
                        Posts: 851
                        Philby Offline
                        Philby
                        wrote on last edited by
                        #6 Quote Reply

                          :tu: I've always sharpened free hand, but now you've got me wondering about getting a system! :facepalm:

                          1 Reply Last reply
                          • Sorel Offline
                            Sorel
                            Posts: 28
                            Sorel Offline
                            Sorel
                            wrote on last edited by
                            #7 Quote Reply

                              The Sharpmaker's good for the wounded egos of those of us who sharpen poorly by hand, because - you're still doing it by hand, but it works :)

                              1 Reply Last reply
                              • SAK Guy Offline
                                SAK Guy
                                Posts: 23,929
                                SAK Guy Offline
                                SAK Guy
                                wrote on last edited by
                                #8 Quote Reply

                                  @Philby said:
                                  :tu: I've always sharpened free hand, but now you've got me wondering about getting a system! :facepalm:

                                  :tu: Freehand (but it took 35 years or so to get fairly good at it)! I'm too impatient to use a system.

                                  1 Reply Last reply
                                  • neillcurrie Offline
                                    neillcurrie
                                    Posts: 860
                                    neillcurrie Offline
                                    neillcurrie
                                    wrote on last edited by
                                    #9 Quote Reply

                                      I tried 20 degrees on the Lansky, but found that I was always grinding the corners of the Lansky rather than the blade. Obviously worst on the smaller blades.
                                      Up a notch, and 25 degrees works fine(no corner grinding), even with the smallest Vic blades, still slices really well.

                                      1 Reply Last reply
                                      • microbe Offline
                                        microbe
                                        Posts: 2,340
                                        microbe Offline
                                        microbe
                                        wrote on last edited by
                                        #10 Quote Reply

                                          @neillcurrie said:
                                          I tried 20 degrees on the Lansky, but found that I was always grinding the corners of the Lansky rather than the blade. Obviously worst on the smaller blades.
                                          Up a notch, and 25 degrees works fine(no corner grinding), even with the smallest Vic blades, still slices really well.

                                          Once the corners are off, the lansky is perfect at 20 degees.

                                          1 Reply Last reply

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login

                                          1. Home
                                          2. Tool Talk
                                          3. Swiss Army Knights Forum
                                          4. Sharpening angle
                                          Reply
                                          • Reply as topic
                                          Log in to reply
                                          COMMUNITY LINKS
                                          EDC-TV SAKWiki GearFeed SAKSelector
                                          Operational Funds

                                          Help us keep the Unworkable working!

                                          Make A Donation
                                          November Goal: $300.00
                                          Due Date: Nov 30
                                          Total Receipts: $0.00
                                          Below Goal: $300.00
                                          0% funded
                                          • Login

                                          • Don't have an account? Register

                                          • Login or register to search.
                                          • First post
                                            Last post
                                          0