Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Polishing tips needed

Scheduled Pinned Locked Moved General Tool Discussion
4 Posts 1 Posters 917 Views
  1. Home
  2. Tool Talk
  3. General Tool Discussion
  4. Polishing tips needed
Polishing tips needed
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • tosh Offline
    tosh
    Posts: 3,181
    tosh Offline
    tosh
    wrote on last edited by tosh
    Quote Reply

      I have a certain something on the way, not letting on until it arrives. :D
      In the meantime I would like some tips on polishing.

      I also have a Pair of LM satin sideclips and have often wondered if one could be buffed up as the satin finish has numerous highlights.

      I'm not wanting to spend anything if possible.. :twak:

      Buried somewhere in the garage is a Rolson Polishing Kit and a vintage Black & Decker Powerstation fitted with a chuck that I picked up years ago.

      (I've copied pics off the web)

      Any tips would be greatly appreciated :tu:

      48889pack.jpg

      download (17).jpg

      1 Reply Last reply
      • babola Offline
        babola
        Posts: 1,629
        babola Offline
        babola
        wrote on last edited by
        #1 Quote Reply

          That should be fine. However I'd suggest you give the bead blasted finish of the Sideclip a once over with the 1500-2000 grit sand paper first. This will provide some pre-polish treatment to the surface (it will appear polished but it will be a 'rough' polished finish and still show fine sanding lines under an angle) and shorten the time and effort you'd have to spend later on polishing directly a bead blasted finish.

          I've done this with the matte bead-blasted Gerber MP600 which I polished to a mirror shine, sorry no pics as it's now long sold.

          Any questions, just shoot.

          Happy buffing! :tu:

          1 Reply Last reply
          • tosh Offline
            tosh
            Posts: 3,181
            tosh Offline
            tosh
            wrote on last edited by
            #2 Quote Reply

              Cheers babola

              As for the MP600, funnily enough I just considered doing exactly the same to the recent Pro-Scout I picked up with the bent blade - I'm guessing it would look very similar to the mp600 clones (winchester, fiskar)

              Does the tool need to be stripped to its barest components to get the best results and would you recommend doing the same if I decide to polish the sideclip.

              Did you also buff inside the handles too?

              1 Reply Last reply
              • babola Offline
                babola
                Posts: 1,629
                babola Offline
                babola
                wrote on last edited by babola
                #3 Quote Reply

                  @tosh said:
                  Cheers babola

                  As for the MP600, funnily enough I just considered doing exactly the same to the recent Pro-Scout I picked up with the bent blade - I'm guessing it would look very similar to the mp600 clones (winchester, fiskar)

                  Does the tool need to be stripped to its barest components to get the best results and would you recommend doing the same if I decide to polish the sideclip.

                  Did you also buff inside the handles too?

                  It's always better to take the handles apart if you can, on some tools could be a little challenging due to non-standard screws etc. I didn't take the MP600 apart as I wasn't sure if I could remove the two bottom handle screws without damaging the head. Nevertheless, it came out beautiful and surprisingly even polished. Sideclip should be easier in this respect as its 8 pentalobe T10S screws should be easy to remove. Just don't forget to use a flame torch for 20-30 seconds on them first to loosen up the Loctite. Older LM tools come with generous amount of Loctite applied.

                  As for the insides of the handles, just leave them be, no need to touch them.

                  If you're planning to do a Greber, they pretty much all come fully bead-blasted and require a little bit more effort especially if you're planning on doing the pliers head too.

                  On my MP600 I polished the handles but applied brushed (a la Leatherman style) finish on the pliers - they came out fantastic. I removed the pliers first, of course.

                  :)

                  1 Reply Last reply

                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                  With your input, this post could be even better 💗

                  Register Login

                  1. Home
                  2. Tool Talk
                  3. General Tool Discussion
                  4. Polishing tips needed
                  Reply
                  • Reply as topic
                  Log in to reply
                  COMMUNITY LINKS
                  EDC-TV SAKWiki GearFeed SAKSelector
                  Operational Funds

                  Help us keep the Unworkable working!

                  Make A Donation
                  November Goal: $300.00
                  Due Date: Nov 30
                  Total Receipts: $0.00
                  Below Goal: $300.00
                  0% funded
                  • Login

                  • Don't have an account? Register

                  • Login or register to search.
                  • First post
                    Last post
                  0