Assorted make-them-yourself bit drivers
-
I appreciate the Leatherman Tool Adapter (I own one), and the Universal Tool Adapter. They are nicely made, very sturdy, and it's nice that they operate at 45 and 90 degrees, but they are fairly scarce these days, and scarcity brings cost (currently there are two on ebay, with BIN's of $50 and $70). They are also pretty heavy.
The large flat screwdriver on many early Leatherman Tools lends itself to an easy to make adapter that fits via magnets, is very cheap to make, operates at any angle the flat driver can be positioned in, and the adapters are very lightweight. I made two adapters for my PST and PST2, one drives 1/4" bits, the other drives the large selection of 4mm bits I have already that fit my Victorinox Cybertool. I used tiny rare earth magnets that detron kindly sent me, one holds in the bit, and I used two magnets to attach the Adapter to the Leatherman. All the magnets are invisible, being held inside the Adapters in the JB Weld that sets everything solid. Magnetic retention is sufficiently firm that I can easily lift the Leatherman PST via holding onto the end of the bit. Any angle that you can use the large flat driver at, is fine with these adapters: no need to "restrict yourself" to the 45 or 90 degree settings of the original Tool Adapter!
There's a side benefit too of using this method for driving bits, the adapters also fit many other multi-tools that use a similarly sized flat driver: some SOG's work, as do certain other much newer Leathermen. The Mini tool even drives them OK via the file/flat driver, although there is a little wiggle.
Construction tips. I used the slow-curing version of JB Weld, and set the items for curing on the top of my oil furnace. It's around 70 degrees there, and it cures a good bit faster than in our glacial house. Obviously I used the PST or PST2 large flat drivers as moulds, a thin layer of grease worked so-so as a "release agent", otherwise the JB Weld will stick everything together royally. A layer of thin plastic tape, Priority Mail tape, releases even better I found. I placed the magnets on the end of a 4mm or 1/4" bit, applied a little JB, stuck it inside the socket.......then placed two magnets on either side of the large flat driver, placed the driver as far inside the socket as possible, filled everything with JB, then set everything to cure on the furnace, using Vice Grips to hold everything square and parallel while the JB set. After about 12 hours I yanked everything apart, and filed the JB Weld flat to the level of the socket. Since the Leatherman flat driver is asymmetric, I dremeled a marker into the socket to indicate which way to put the socket on the driver, though even without the mark it's pretty obvious. Job done.
Try it, it's pretty easy, and quite satisfying :) ;) -
That is great!
I actually had the exact same concept a couple of months back and made it in plastic, fitting most 91mm Victorinox flat screwdrivers. I'll try to get some pictures up as well.
I've been worried about using too much torque which would break the multitool (though with the plastic I've used to prototype, it's the plastic wearing out first). What's your idea on that? -
@arnoldus said:
That is great!
I actually had the exact same concept a couple of months back and made it in plastic, fitting most 91mm Victorinox flat screwdrivers. I'll try to get some pictures up as well.
I've been worried about using too much torque which would break the multitool (though with the plastic I've used to prototype, it's the plastic wearing out first). What's your idea on that?I've not used the adapters seriously yet so I can't speak to durability. However, as an indicator, years ago I had some really nice aluminum brake levers on a MTB, and their mounting bolts were partially stripped. I degreased them, then filled the tapped holes with JB weld, let it set good, then drilled and retapped them. I was still using the levers a year later.
Certain other stronger epoxies advertise that they can be drilled and machined after curing too.
Mostly I see the adapters best when driving the smaller 4mm bits, but even if the larger version fails its no big deal. What am I really out, a generic socket? -
I have been making SAK adapters pretty much the same way for years. It works good and they hold up well. The process is called bedding its used in gun smithing for making actions fit stocks with a nice tight fit. I have used release agent that comes with bedding kits, johnsons paste wax and Pam cooking spray. When I use paste wax I let it dray all the way before putting it in the wet J-B Weld. Pam cooking works good so I mostly use it. I have never heard of using tape but hey if it works.
Mike -
Nice work, Neil

BTW, love the look of those hammered pivot and screws heads on the PST ;)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login