Scale replacement question.
-
Talking about SAKs with swapped scales - Did you receive the CT yet?!
-
I also have only used my hands , I think 1 time a few years back I had to put one in a small jewelers vise.
-
@lowtech said:
Talking about SAKs with swapped scales - Did you receive the CT yet?!Nah not yet, seems the guy I bought it from was dragging his feet.

This swap is for a Spartan Syph blacked out and I want to make into a stormtooper looking SAK. Well that and a Super Tinker at some point down the road.
-
Mission complete and it was not as easy as Def made it out to be. That last little bit of gap took some real effort but alls well that ends well.
I did tear up one end of one of the old scales while I learned the best way to get the can opener under the scales. Did not need them though.
So my latest SAK, TK-421.

Spartan mode for now but wil be modded into a Super Tink someday.
-
@HarleyXJGuy said:
Mission complete and it was not as easy as Def made it out to be. That last little bit of gap took some real effort but alls well that ends well.I did tear up one end of one of the old scales while I learned the best way to get the can opener under the scales. Did not need them though.
So my latest SAK, TK-421.

Spartan mode for now but wil be modded into a Super Tink someday.
Serves you right for listening to the bossman. :P
Why in god's green name would you use a can opener? It's too short and too thick, A thin, blunt, wide blade works best (always using my watch opener blade). -
I use the big screwdriver and insert it a the weakest point, top middle. Then I just push toward the bushings and no prying required.
-
Bah now you guys come along and tell me after it is done.

-
@HarleyXJGuy said:
Bah now you guys come along and tell me after it is done.
Hey, I told you to use a hammer.....
-
I use channel locks to put the scales on. I wrap the knife in cardboard first though. Putting brand new scales on is a lot harder by hand than ones that have been removed once though.
-
Really miss my tools on days like this.
-
I use these. But lots of things can do the job. Heating them up gently before removal will help the bushing area not to break.

-
@Corwyn said:
Nope. But it doesn't hurt.Straight way is to put a thin blade at the edge where the toothpick is and pry gently moving to the rivets till it pops open. Afterwards just pop the new ones in place.
The vice is to make sure the new ones are placed firmly and straight with equal pressure on both sides. You could do it by hand or with a plier in most cases but a vice makes it easier (changed dozens of sak scales without a vice).CAUTION: if using a plier or vice put in tons of towels as they might scratch or crack the scales...
Now if you want to be extra sure (and/or if you want to reuse the old scales the safest way is to soak the knife and scales in warm water and soften up the cellidor (not boiling! I melted a pair). The reason is that dry cellidor is brittle and when you force it though the bushings, the outer ring might break and the scales could be ruined.
If you want to change electronic scales, it's even trickier. I found out it works best when heating them with a blow drier to soften them. Put the blade in the battery slot, but take out the battery and door first.
Nice How To: </topic/12903
Nice video: http://www.youtube.com/watch?feature=player_embedded&v=In0HMwJg01g
Is there a special trick that I should know to change out scales that have a light and a pen?
-
Not that I know of. Just remove the pen, pin, tweezers and toothpick before removing the scales. I use warm warm to help soften them.
-
Nope. But it doesn't hurt.
Straight way is to put a thin blade at the edge where the toothpick is and pry gently moving to the rivets till it pops open. Afterwards just pop the new ones in place.
The vice is to make sure the new ones are placed firmly and straight with equal pressure on both sides. You could do it by hand or with a plier in most cases but a vice makes it easier (changed dozens of sak scales without a vice).CAUTION: if using a plier or vice put in tons of towels as they might scratch or crack the scales...
Now if you want to be extra sure (and/or if you want to reuse the old scales the safest way is to soak the knife and scales in warm water and soften up the cellidor (not boiling! I melted a pair). The reason is that dry cellidor is brittle and when you force it though the bushings, the outer ring might break and the scales could be ruined.
If you want to change electronic scales, it's even trickier. I found out it works best when heating them with a blow drier to soften them. Put the blade in the battery slot, but take out the battery and door first.
Nice How To: </topic/12903
Nice video: http://www.youtube.com/watch?feature=player_embedded&v=In0HMwJg01g
Is there a special trick that I should know to change out scales that have a light and a pen?
Hair dryer is the key. Never submerge electronic scales in water
-
I have found that the fine tip screwdriver on the back of my swiss champ fits in the tweezer and toothpick slots perfectly, just a slight twist and the scales pop off without and damage.
-
Ooooh, I just got a set of Green, Red and Black plus scales from someone I cannot thank enough.
I now get to play with which SAK to "upgrade"
Shot Ken! I really appreciate it.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login