wing man scissors on wave
-
It can be done, I believe you'll need to enlarge the pivot hole, but not much else. Check out the Mod Squad board ( http://forum.multitool.org/index.php/board,16.0.html ) to see others' experiences, and this one in particular has some good information:
</post/877470>
-
I think Breezy12 got there first:
@Breezy12 said:
this "skinny Charge" has been a terrific office EDC for me the past few months.

I enlarged the pivot hole, moved the saw to the serrated blade slot and put them where the saw used to be:
<a href="https://flic.kr/p/pJcbwZ" target="_blank" rel="noopener noreferrer"><img src="https://farm6.staticflickr.com/5610/15573680165_f7e3d0104d_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a> -
@eddie1115 said:
It can be done, I believe you'll need to enlarge the pivot hole, but not much else. Check out the Mod Squad board ( http://forum.multitool.org/index.php/board,16.0.html ) to see others' experiences, and this one in particular has some good information:</post/877470>
this is correct -- you just need to enlarge the pivot hole from 3/16" to 7/32" and the scissors will fit nicely. :)
-
CAn you clarify that a little bit as far as how to make the scissors fit. I just put them in a wave without doing anything and they wont spring back open. How do i fox this?
-
Did you file the back of the scissors piece (not the spring piece) so that the liner lock engages? Put up some pics mate.
-
some more details would help... did you put the scissors in place of the saw? is the liner lock engaging properly?
some pics would definitely help...
-
yes, I am replacing the saw. the liner lock doesn't seem to engage properly. the scissors themselves shift down when trying to use them.


-
you may need to file a bit off the back of the scissors (where it meets the liner lock) in order to get the lock to engage properly. take a close look at where the liner lock meets the scissors, and it should be apparent if you need to file/grind the scissors at all.
-
The scissors lock tightly but the spring mech wont shift into position
-
Have you enlarged the pivot hole on the scissors so they fit onto the fastener post?
-
No i have not. Do you mean the holes that the screw goes through? If so, how will this help? (Im not trying to be rude, in just puzzled :P)
-
Yes it was me who broke my Wingman scissors tang while attempting to drill it
instead of using the diamond burr as usual.But I have a question while the experts are on. I note the spring arm is already oversize at a tad under 6mm. Assuming I hadn't smeg'd the first stage does the original clearance between spring arm and post have to be restored?
(I'm guessing Zach must have the scissors piece trapped between post and screw against the liner lock
) -
@pingu said:
Yes it was me who broke my Wingman scissors tang while attempting to drill it
instead of using the diamond burr as usual.But I have a question while the experts are on. I note the spring arm is already oversize at a tad under 6mm. Assuming I hadn't smeg'd the first stage does the original clearance between spring arm and post have to be restored?
(I'm guessing Zach must have the scissors piece trapped between post and screw against the liner lock
)I don't recall changing the spring piece at all. And yeah that is probably what Zach has done.
@Zachbradley said:
No i have not. Do you mean the holes that the screw goes through? If so, how will this help? (Im not trying to be rude, in just puzzled :P)Yes, the hole that the screw goes through has to be large enough to let the post pass through.
The post (not the screw) is what the scissors and spring pivot on.
You may have to file the back of the scissors piece (not the spring piece) so that the liner lock engages.
Tighten the screw all the way so that the spring piece can't be pushed off the post.
File a little and check the fit, rinse and repeat, don't rush it. -
...rinse and repeat...
rinse? What are you doing to the mother country's language

Anyway damn this thread
. It has rekindled my interest in having Wingman scissors in a Wave, or my case my Ve. Also another go at at a single handled Wingman. I do not think I can resist 
I'm smurfing it to death just like
you and those scissorseveryone else does around here. :P -
Yes it was me who broke my Wingman scissors tang while attempting to drill it
instead of using the diamond burr as usual.But I have a question while the experts are on. I note the spring arm is already oversize at a tad under 6mm. Assuming I hadn't smeg'd the first stage does the original clearance between spring arm and post have to be restored?
(I'm guessing Zach must have the scissors piece trapped between post and screw against the liner lock
)I don't recall changing the spring piece at all. And yeah that is probably what Zach has done.
I've done this mod enough times now to say with certainty that the spring piece does not require any modification. :)
-
please pardon my newbiness. I am still not sure how to make this work. Here is how the scissors right now are acting: when locked into place, the scissors are not tight, so they dont spring back up. but when i force them down with my finger and hold it like that, they work like they should. but thats only when i am holding the scissors down with the opposite hand that i am using to press down the thumb pad. Can someone that has done this before please upload some picks showing me what i need to do? I would really appreciate it!
-
No i have not. Do you mean the holes that the screw goes through? If so, how will this help? (Im not trying to be rude, in just puzzled :P)
Yes, the hole that the screw goes through has to be large enough to let the post pass through.
The post (not the screw) is what the scissors and spring pivot on.
You may have to file the back of the scissors piece (not the spring piece) so that the liner lock engages.
Tighten the screw all the way so that the spring piece can't be pushed off the post.
File a little and check the fit, rinse and repeat, don't rush it.Did you read this? How much of it do you understand? Enlarged the pivot hole yet?
-
@Zachbradley said:
please pardon my newbiness. I am still not sure how to make this work. Here is how the scissors right now are acting: when locked into place, the scissors are not tight, so they dont spring back up. but when i force them down with my finger and hold it like that, they work like they should. but thats only when i am holding the scissors down with the opposite hand that i am using to press down the thumb pad. Can someone that has done this before please upload some picks showing me what i need to do? I would really appreciate it!I have some pics that might help, but they're on my home computer. (I'm still at work.) I'll try to post some this weekend.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login