Cybertool Bit Driver Difference
-
as you see at the photo above, 29 and 41 have a slightly different shaped and colored bit driver than on 34 and lite.
according the information we took from Robert Elsener on our Facebook page "Swiss Army Knives Collectors" ; before 2010 victorinox uses a non-alloyed steel that has low resistance to corrosion and therefore is was nickel plated (the golden ones on 34 and lite), since 2010 bit driver is made of stainless steel.
-
Very interesting. I just looked at a bunch of CT drivers and I'm having a hard time seeing the difference. I'll look after work tonight to see if I can see any other differences.
-
photo below shows the molding line and color difference better...

-
Interesting. I have a CT29 with the line on it.
-
@nervium said:
photo below shows the molding line and color difference better...The moldling line seems to be hit-or-miss. I looks at two CT29s made before 2008 and they both had it; however two CT34s made pre-2004 did not. I'll look more tonight is different lighting and see if I can see a color difference.
-
Change happened in 2013.
GigaHz first noticed it on the run of Dash4it SAKs a bunch of us got.
Here's a link to that thread.
</post/813084>
-
-
dear Robert Elsener said it happened it 2010. i will examine the link.
-
I have to check my other CT, but my 29 and older 41 do not have retention nubs
-
What strikes me is the position of the driver.This is the reason that I haven't bought the CT-34 or 41.The position doesn't allow a smooth revolution of the tool when deploying the driver.It rotates in the hand in a very awkward manner.
On the other hand,because the driver is more centered in the CT-29 and 34-Lite,it revolves in the hand more smoothly.
I may buy the CT-34 and 41 in the future but simply for the purpose of collecting.
-
@toolguy said:
What strikes me is the position of the driver.This is the reason that I haven't bought the CT-343 or 41.The position doesn't allow a smooth revolution of the tool when deploying the driver.It rotates in the hand in a very awkward manner.On the other hand,because the driver is more centered in the CT-29 and 34-Lite,it revolves in the hand more smoothly.
I may buy the CT-34 and 41 in the future but simply for the purpose of collecting.
Honestly, that's never been a problem for me. In the 90 degree position, it is really amazingly good.
-
-
@Mr. Whippy said:
What strikes me is the position of the driver.This is the reason that I haven't bought the CT-343 or 41.The position doesn't allow a smooth revolution of the tool when deploying the driver.It rotates in the hand in a very awkward manner.
On the other hand,because the driver is more centered in the CT-29 and 34-Lite,it revolves in the hand more smoothly.
I may buy the CT-34 and 41 in the future but simply for the purpose of collecting.
Honestly, that's never been a problem for me. In the 90 degree position, it is really amazingly good.
Using the driver in the 90 degree position can be useful in applying more torque but it's still more awkward and allows only partial rotation.I'm sure most of us have done that at times with the top side tools,especially the cap lifter/screwdriver.
-
Just for reference for those not on facebook.
To produce the CyberTool wrench, the MIM technology is used (Metal Injection Molding). Metal Injection Molding is a manufacturing process which combines the versatility of plastic injection molding with the strength and integrity of machined, pressed or otherwise manufactured small, complex, metal parts.
Before 2010, we use a non-alloyed steel that has low resistance to corrosion and therefore is was nickel plated. An economical production with material that are said to be «stainless» or «rust-free» was not possible to date.
Since 2010, the CyberTool wrench is made of stainless steel
The manufacturing process MIM is the same, however, hardening and polishing is different and of course they are not nickel plated anymore
And my questions to the sales of the same:
Hi, Robert Elsener, can you confirm when the Cybertools with these new bit wrenches started to sell. We started noticing them only in spring of 2013, along with the change of the plastic bit holder.

We usually notice such things early on so I'm guessing you (and the dealers too) had to clear out old stock of Cybertools first before these new wrenches hit the shelves.
Also, my Cybertool 34 with new bit wrench has the VICTORINOX/Swiss Made/Stainless tang stamp with all letters the same size, a change that I believe happened sometime in 2011. Until then the V in VICTORINOX was slightly larger than other letters.
No replies as of yet.
-
A strange note. I had 3 CTs on one knife pivot. When open none of the three lined up. All opened at different angles. I have modded 2 different Cts with 2 CTs on one knife, when opened they all have different open angles. I thought the CT was stamped or cast then finished. I am leaning more towards handmade now. I know there are two different metals. I think the line is how much they decided to smooth or polish it. Just rambling after a few beers.
-
OK, this can't be right, can it?
The CyberTool with 29, 34 or 41 functions was developed for electronic engineers and for IT-professionals. The design of the bit case was improved in 2002!
jazzbass, do your older CTs have this updated bit carrier?
-
@toolguy said:
What strikes me is the position of the driver.This is the reason that I haven't bought the CT-34 or 41.The position doesn't allow a smooth revolution of the tool when deploying the driver.It rotates in the hand in a very awkward manner.On the other hand,because the driver is more centered in the CT-29 and 34-Lite,it revolves in the hand more smoothly.
I may buy the CT-34 and 41 in the future but simply for the purpose of collecting.
What Tool said.
When I mod my CT-Lite dropping the lite/mag layer and adding saw/file I will do my best to center the driver.
-
@enki_ck said:
OK, this can't be right, can it?The CyberTool with 29, 34 or 41 functions was developed for electronic engineers and for IT-professionals. The design of the bit case was improved in 2002!
jazzbass, do your older CTs have this updated bit carrier?
While 2002 sounds a bit early to me, I do believe the change was made a while ago. The oldest CT I have with the new bit holder is an XXLT, so it's a pre-2005 change.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login