Swisstool Pivot Play?
-
I just received a Swisstool. From the stickied thread, I believe it is a 1998 model.
I definitely like it, but have a few quick questions after playing with it for only a few minutes.
The pivot for the plier heads seems very loose and jangly.
The handles have a little lateral play, i.e. you can move them just a little perpendicular to the pivot. They make a little rattling noise at the pivot when you do this.
And the handles swing very freely. It's a little hard to describe. Basically, the handles aren't tight and don't have any snap. They just kind of hang there. They feel extremely different from any of my previous pliers or even my Kick. I don't know, this could be a good thing, for all I know.
My other question was regarding the wirecutters. A picture of the 1998 ST elsewhere doesn't show a hard wire notch. I think mine has one, but it is hard to tell whether it is a notch or just damage.
The notch is just a little flattened dent near the base of the wirecutting area on both sides. It is not sharp at all. It is like the wirecutters were squished around something.
Is that what is is supposed to look like? The only other tool I have with a hard wire notch is the Kick, and it doesn't look similar at all to this.
Everything else seems fantastic. I am really impressed with the design. I just need to clear away these 2 little questions first so I can relax and enjoy it... ;)
-
Don't worry about the pivot play.. I few of my SwissTools have it too.. It's not to worry about, really.. I am not to sure about the lateral play in the handles though... Oh, and for the wire cutters, is their any friction when you open and close them? If not, they're fine.
-
No, there's no friction when I open and close the wire cutters.
The lateral wiggle in the handles is extremely slight, but it is enough to make a rattling sound in the pivot area. And it doesn't take very much. I can almost do it with one finger.
It sounds a lot like J-sews demo of the Surge rattle. Actually, I can even do what you mentioned with the Surge - if I hold it by one handle and very gently shake it sideways, it rattles.
My Kick and even my cheapest pliers don't jiggle at all when I try to move the handles laterally. Everything else is tight and crisp, just like my SAKs. That is why the pivot caught me so offguard...
-
If it bothers you send it back to Victorinox. They will replace it and you will get a new one within a week and a half..
-
I was looking back through the old posts and noticed that your Swisstool had a very similar problem, and someone else mentioned a similar issue with their ST.
Actually, your description of the problems with your plier pivot sounded exactly like mine. I just noticed that if I put light pressure on the handle, I can actually see a small gap in the pivot.
I might just try the warranty idea. I also have a Vic Ranger I might send in - it is brand new but has a weird glitch on the tip of the metal file.
I am very nervous though, as I have had a streak of bad luck in my dealings with almost everyone lately, and I don't expect it to be that easy...
-
What do you mean by a glitch in the file? Oh, and don't be nervous about using Vic's warranty service. I've used Gerber's. SOG's, Leatherman's, and Victorinox's warranty and I think Vic's is the best! Mind you, I am a Leatherman guy! Oh, and I am willing to bet that your SwissTool and Ranger will not come at the same time.. Knife warranty work takes a longer time. My SwissTool had the pivot play severely and they replaced it with a brand new model free of charge.. I also sent a SwissChamp and a CyberTool 34 that were both repaired and I got them a few days after receiving my new SwissTool! I hope this helps!
-
The problem with the metal file on my Ranger is very, very minor and also hard to describe. The last 1/2 mm of the tip of the metal file is slightly deformed on one side and the tip is a little blunted. If you run your fingernail along it, you can feel a little drop just before you hit the tip. You can see a little ripple in the metal where this happens. At first, I thought someone had lied about the SAK being new and had damaged the tip trying to pry something, but after looking at it a little more, I am pretty sure it came that way.
It is an extremely minor thing, but I can't imagine that it is not a defect of some sort. The knife is brand new and I have never seen another tool on a Vic or Wenger that has a sloppy tip or edge like that.
I use the metal file as a nail file and you can feel the tip scratching under your nails, etc. I was going to try and file it smooth myself, but was thinking it might be worth seeing whether Vic will fix it instead since I am sending the Swisstool in anyway.
I have no idea whether they will even see it though. It is pretty minor, though I did notice it within a few seconds of taking it out of the box. I guess they are experts though, so hopefully they will see it as a quickly as I did.
Both tools are absolutely flawless other than those 2 issues. I really, really like the design of the Swisstool, and the Ranger is a powerhouse tool combination.
Incidentally, I was always curious about the shape and cutouts on many of the tools on the Swisstool. Like the dent on the top of the can opener and the curve on the philips head. Now I can finally see that the cutouts are so you can access the nail nicks on the other tools, and that the philips is shaped that way to improve torque. I love that kind of stuff. Those wizards at Vic never let me down... :)
-
You will get an 05 SwissTol back as well.
-
That would be nice. I like the 2005 plier head the best, though I think it won't open as wide.
You have almost every version of ST. Are the plier heads the only thing that changed between 1998 and 2005?
-
I wouldn't worry too much about the condition of your ST, but like Nikko said, you could always just send it back :)
And yeah, it's in the details that you really learn to understand how great the St is :)
-
Speaking of details, I just noticed that the sides of each handle are different widths. The blade side of each handle is higher than the other side of the same handle.
I assume it is because the blades are much wider than the saw and file which are opposite them...

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login