Wave screws problem
-
Cheers, everybody.
So the file was a bit loose on my Wave out of the box, I've bought those torx bits and decided to tighten things up. Did it, now the file is well held in place, however the knife opens at the same time too tight and the screw rotates a little while I open/close knife or file.
What did I ruin? How do I make things right? :) -
Try loosening it just a bit.
-
The screws have some threadlock around them when they are assembled, so to take the tool apart, easily, it is usually suggested that you heat up the screw area, to release the threadlock.
Now, after you put it back together you too can also add some threadlock or suitable glue, to keep the screws from turning.
-
I'm not sure this is a threadlock issue (unless only the screw is turning). I only currently have a single arm Wave (or Ve). When I went to check I was surprised to note the bolt and screw rotated as one. Actually the file is held closed by the liner-lock dimple when the opposite tool is deployed. The other side is Wingman scissors. I suspect I have failed to drill a relief hole for the dimple but friction keeps it closed when the file is deployed.
It has been suggested to loosen the screw a little. Just to be different I'm guessing it needs to be a tad tighter to keep the dimple on the liner lock engaged.
-
Does both sides turn same amount? Then no worries. If both sides move on own, add threadlock (locktite).
-
Just play with the screw tension a bit. I can usually dial it in to a sweet spot at which point, loctite it there. This is typical behaviour on most of the Wave's I've owned and is due to the screws sitting on top of the tool with no washer in between.
-
Thanks a lot, guys, loosened it a tiniest bit and it did the trick for now - I guess I've found the sweet spot where both file and knife perform as expected :)
-
@alexanderre said:
Thanks a lot, guys, loosened it a tiniest bit and it did the trick for now - I guess I've found the sweet spot where both file and knife perform as expected :)Good stuff! Now would be a great time to add loctite
. -
Thanks a lot, guys, loosened it a tiniest bit and it did the trick for now - I guess I've found the sweet spot where both file and knife perform as expected :)
Good stuff! Now would be a great time to add loctite
.Do you have any video instruction on how to do it right? Cause I'm not quite sure what to do
Dream. Wish. Leave nothing undone. Repeat.
-
Just add a small drop to the threads of the screw and replace the screw

-
@sawman said:
Just add a small drop to the threads of the screw and replace the screw
Oh, I see, thanks, maybe I'll try that if needed, but for now those don't screws don't rotate anymore and everything just works all right. If I'll find some new issues with it - will do just what you guys suggest, but for now it just seems to have been overtightened.
Dream. Wish. Leave nothing undone. Repeat.
-
Just add a small drop to the threads of the screw and replace the screw

Oh, I see, thanks, maybe I'll try that if needed, but for now those don't screws don't rotate anymore and everything just works all right. If I'll find some new issues with it - will do just what you guys suggest, but for now it just seems to have been overtightened.
Dream. Wish. Leave nothing undone. Repeat.
Goodluck and keep us posted as time progresses with this.
-
Just add a small drop to the threads of the screw and replace the screw

Oh, I see, thanks, maybe I'll try that if needed, but for now those don't screws don't rotate anymore and everything just works all right. If I'll find some new issues with it - will do just what you guys suggest, but for now it just seems to have been overtightened.
Dream. Wish. Leave nothing undone. Repeat.
Goodluck and keep us posted as time progresses with this.
oh, sure thing, thanks again [emoji482]
Dream. Wish. Leave nothing undone. Repeat.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login