Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Wave screws problem

Scheduled Pinned Locked Moved Leatherman Tools
13 Posts 1 Posters 1.3k Views
  1. Home
  2. Tool Talk
  3. Leatherman Tools
  4. Wave screws problem
Wave screws problem
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • in_sympathy Offline
    in_sympathy
    Posts: 1,532
    in_sympathy Offline
    in_sympathy
    wrote on last edited by
    Quote Reply

      Cheers, everybody.
      So the file was a bit loose on my Wave out of the box, I've bought those torx bits and decided to tighten things up. Did it, now the file is well held in place, however the knife opens at the same time too tight and the screw rotates a little while I open/close knife or file.
      What did I ruin? How do I make things right? :)

      1 Reply Last reply
      • SteveC Offline
        SteveC
        Global Moderators
        Posts: 73,535
        SteveC Offline
        SteveC
        Global Moderators
        wrote on last edited by
        #1 Quote Reply

          Try loosening it just a bit.

          1 Reply Last reply
          • dks Offline
            dks
            Posts: 21,823
            dks Offline
            dks
            wrote on last edited by
            #2 Quote Reply

              The screws have some threadlock around them when they are assembled, so to take the tool apart, easily, it is usually suggested that you heat up the screw area, to release the threadlock.

              Now, after you put it back together you too can also add some threadlock or suitable glue, to keep the screws from turning.

              1 Reply Last reply
              • pingu Offline
                pingu
                Posts: 487
                pingu Offline
                pingu
                wrote on last edited by pingu
                #3 Quote Reply

                  I'm not sure this is a threadlock issue (unless only the screw is turning). I only currently have a single arm Wave (or Ve). When I went to check I was surprised to note the bolt and screw rotated as one. Actually the file is held closed by the liner-lock dimple when the opposite tool is deployed. The other side is Wingman scissors. I suspect I have failed to drill a relief hole for the dimple but friction keeps it closed when the file is deployed.

                  It has been suggested to loosen the screw a little. Just to be different I'm guessing it needs to be a tad tighter to keep the dimple on the liner lock engaged.

                  1 Reply Last reply
                  • Crow Offline
                    Crow
                    Posts: 2,525
                    Crow Offline
                    Crow
                    wrote on last edited by
                    #4 Quote Reply

                      Does both sides turn same amount? Then no worries. If both sides move on own, add threadlock (locktite).

                      1 Reply Last reply
                      • Toolslinger Offline
                        Toolslinger
                        Posts: 2,453
                        Toolslinger Offline
                        Toolslinger
                        wrote on last edited by
                        #5 Quote Reply

                          Just play with the screw tension a bit. I can usually dial it in to a sweet spot at which point, loctite it there. This is typical behaviour on most of the Wave's I've owned and is due to the screws sitting on top of the tool with no washer in between.

                          1 Reply Last reply
                          • in_sympathy Offline
                            in_sympathy
                            Posts: 1,532
                            in_sympathy Offline
                            in_sympathy
                            wrote on last edited by
                            #6 Quote Reply

                              Thanks a lot, guys, loosened it a tiniest bit and it did the trick for now - I guess I've found the sweet spot where both file and knife perform as expected :)

                              1 Reply Last reply
                              • Toolslinger Offline
                                Toolslinger
                                Posts: 2,453
                                Toolslinger Offline
                                Toolslinger
                                wrote on last edited by
                                #7 Quote Reply

                                  @alexanderre said:
                                  Thanks a lot, guys, loosened it a tiniest bit and it did the trick for now - I guess I've found the sweet spot where both file and knife perform as expected :)

                                  Good stuff! Now would be a great time to add loctite :tu:.

                                  1 Reply Last reply
                                  • in_sympathy Offline
                                    in_sympathy
                                    Posts: 1,532
                                    in_sympathy Offline
                                    in_sympathy
                                    wrote on last edited by
                                    #8 Quote Reply

                                      @Toolslinger said:

                                      @alexanderre said:

                                      Thanks a lot, guys, loosened it a tiniest bit and it did the trick for now - I guess I've found the sweet spot where both file and knife perform as expected :)

                                      Good stuff! Now would be a great time to add loctite :tu:.

                                      Do you have any video instruction on how to do it right? Cause I'm not quite sure what to do


                                      Dream. Wish. Leave nothing undone. Repeat.

                                      1 Reply Last reply
                                      • sawman Offline
                                        sawman
                                        Posts: 9,745
                                        sawman Offline
                                        sawman
                                        wrote on last edited by
                                        #9 Quote Reply

                                          Just add a small drop to the threads of the screw and replace the screw :tu:

                                          1 Reply Last reply
                                          • in_sympathy Offline
                                            in_sympathy
                                            Posts: 1,532
                                            in_sympathy Offline
                                            in_sympathy
                                            wrote on last edited by
                                            #10 Quote Reply

                                              @sawman said:
                                              Just add a small drop to the threads of the screw and replace the screw :tu:

                                              Oh, I see, thanks, maybe I'll try that if needed, but for now those don't screws don't rotate anymore and everything just works all right. If I'll find some new issues with it - will do just what you guys suggest, but for now it just seems to have been overtightened.


                                              Dream. Wish. Leave nothing undone. Repeat.

                                              1 Reply Last reply
                                              • sawman Offline
                                                sawman
                                                Posts: 9,745
                                                sawman Offline
                                                sawman
                                                wrote on last edited by
                                                #11 Quote Reply

                                                  @alexanderre said:

                                                  @sawman said:

                                                  Just add a small drop to the threads of the screw and replace the screw :tu:

                                                  Oh, I see, thanks, maybe I'll try that if needed, but for now those don't screws don't rotate anymore and everything just works all right. If I'll find some new issues with it - will do just what you guys suggest, but for now it just seems to have been overtightened.


                                                  Dream. Wish. Leave nothing undone. Repeat.

                                                  Goodluck and keep us posted as time progresses with this.

                                                  1 Reply Last reply
                                                  • in_sympathy Offline
                                                    in_sympathy
                                                    Posts: 1,532
                                                    in_sympathy Offline
                                                    in_sympathy
                                                    wrote on last edited by
                                                    #12 Quote Reply

                                                      @sawman said:

                                                      @alexanderre said:

                                                      @sawman said:

                                                      Just add a small drop to the threads of the screw and replace the screw :tu:

                                                      Oh, I see, thanks, maybe I'll try that if needed, but for now those don't screws don't rotate anymore and everything just works all right. If I'll find some new issues with it - will do just what you guys suggest, but for now it just seems to have been overtightened.


                                                      Dream. Wish. Leave nothing undone. Repeat.

                                                      Goodluck and keep us posted as time progresses with this.

                                                      oh, sure thing, thanks again [emoji482]


                                                      Dream. Wish. Leave nothing undone. Repeat.

                                                      1 Reply Last reply

                                                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                      With your input, this post could be even better 💗

                                                      Register Login

                                                      1. Home
                                                      2. Tool Talk
                                                      3. Leatherman Tools
                                                      4. Wave screws problem
                                                      Reply
                                                      • Reply as topic
                                                      Log in to reply
                                                      COMMUNITY LINKS
                                                      EDC-TV SAKWiki GearFeed SAKSelector
                                                      Operational Funds

                                                      Help us keep the Unworkable working!

                                                      Make A Donation
                                                      November Goal: $300.00
                                                      Due Date: Nov 30
                                                      Total Receipts: $0.00
                                                      Below Goal: $300.00
                                                      0% funded
                                                      • Login

                                                      • Don't have an account? Register

                                                      • Login or register to search.
                                                      • First post
                                                        Last post
                                                      0