Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Sebenza edges

Scheduled Pinned Locked Moved Edged Tools
6 Posts 1 Posters 1.3k Views
  1. Home
  2. Tool Talk
  3. Edged Tools
  4. Sebenza edges
Sebenza edges
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • kwakster Offline
    kwakster
    Posts: 1,006
    kwakster Offline
    kwakster
    wrote on last edited by
    Quote Reply

      I've sharpened quite a few Sebenza's for others, and how i sharpen them is based on both personal experience and user feedback.
      On older ones i've learned that the lowest angle i can reprofile them to lies around 35 degrees inclusive, and that i have to keep the edge finish rather coarse to still have quite good edge retention.
      On newer ones i can lower the edge angle to around 30 degrees inclusive, and i also can refine the edge more, yet still have good edge retention.
      Other people may have other ideas, but this is what i've found to work well.

      Yesterday i did this regular Sebenza from 2005 in S30V steel, which is the favorite folder of a professional hunter.
      The old factory edge was kept more or less sharp by him with stropping only, and the edge angle measured 35-40 degrees inclusive on the straight part and well over 40 degrees inclusive from the belly to the tip.
      I reprofiled the edge to an even 35 degrees inclusive from heel to tip on my Rubber Wheel covered with 230 grit diamond powder (covered in wax to prevent any damage due to overheating), and only removed the burr with the Tormek leather wheel coated with 1 micron diamond compound.
      This removes the burr gently but efficiently, while at the same time leaving the scratch pattern intact as much as possible to preserve bite (something i specifically aim for)
      The Rubber Wheel has a tiny amount of "give" in it's surface which provides for an ever so slight convexity in the new edge, and the use of diamonds makes sure that the vanadium carbide particles in the steel are cleanly cut.
      The resulting coarse edge both favors the S30V steel type and the actual use it will see in the hands of the hunter, and it's treetopping sharp with lots of bite.

      No "before" pics this time (i forgot), but below are the result pics i also sent to the owner.

      <a href="http://postimg.org/image/sdok4ai5t/" target="_blank" rel="noopener noreferrer"><img src="http://s16.postimg.org/sdok4ai5t/GEDC8666.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a><a href="http://postimg.org/image/n9sp2cho1/" target="_blank" rel="noopener noreferrer"><img src="http://s16.postimg.org/n9sp2cho1/GEDC8667.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

      <a href="http://postimg.org/image/qzwx8ziwh/" target="_blank" rel="noopener noreferrer"><img src="http://s16.postimg.org/qzwx8ziwh/GEDC8668.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a><a href="http://postimg.org/image/n0v4cf4vl/" target="_blank" rel="noopener noreferrer"><img src="http://s16.postimg.org/n0v4cf4vl/GEDC8669.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

      <a href="http://postimg.org/image/bjerkyovl/" target="_blank" rel="noopener noreferrer"><img src="http://s16.postimg.org/bjerkyovl/GEDC8670.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a><a href="http://postimg.org/image/e4kc8he9d/" target="_blank" rel="noopener noreferrer"><img src="http://s16.postimg.org/e4kc8he9d/GEDC8672.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

      <a href="http://postimg.org/image/htemlpdo1/" target="_blank" rel="noopener noreferrer"><img src="http://s16.postimg.org/htemlpdo1/GEDC8674.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a><a href="http://postimg.org/image/j9q53ugkx/" target="_blank" rel="noopener noreferrer"><img src="http://s16.postimg.org/j9q53ugkx/GEDC8676.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

      <a href="http://postimg.org/image/mvvyghmy9/" target="_blank" rel="noopener noreferrer"><img src="http://s16.postimg.org/mvvyghmy9/GEDC8677.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

      1 Reply Last reply
      • kwakster Offline
        kwakster
        Posts: 1,006
        kwakster Offline
        kwakster
        wrote on last edited by
        #1 Quote Reply

          The reason why i started this thread was because i was wondering if Sebenza owners on this forum had anything to contribute regarding the edge holding of their pre-2013 Sebenza models, as somewhere during that year CRK seems to have decided to harden their blades to 59-60 HRC instead of the usual target hardness of 58-59 HRC.

          On the Dutch forum there are at least a few owners who were less then satisfied with the edge holding of their beloved Sebbies, especially when the edge angle was taken down to +/- 30 degrees inclusive, an angle that can be considered a good rule of thumb when sharpening modern knife steels.
          Spyderco for instance specifically target their edges to come out at that angle after factory sharpening.

          1 Reply Last reply
          • sawman Offline
            sawman
            Posts: 9,745
            sawman Offline
            sawman
            wrote on last edited by
            #2 Quote Reply

              That is very impressive, Robert :2tu:

              1 Reply Last reply
              • kwakster Offline
                kwakster
                Posts: 1,006
                kwakster Offline
                kwakster
                wrote on last edited by
                #3 Quote Reply

                  Thanks Steve, :D

                  Also found this thread from 2012/2013 on Bladeforums where members talk about having their Sebenza blades rehardened, apparently with good results:

                  http://www.bladeforums.com/forums/showthread.php/1018932-Where-to-send-sebenza-blade-for-heat-treating

                  1 Reply Last reply
                  • HarleyXJGuy Offline
                    HarleyXJGuy
                    Posts: 8,856
                    HarleyXJGuy Offline
                    HarleyXJGuy
                    wrote on last edited by
                    #4 Quote Reply

                      Seems to me if you pay that much for a Sebby you could get a better HT and maybe some 10V.

                      Not bashing just wonder.

                      Merit Badges
                      LM Surge Challenge Level 3 Skeletool 30 Day Challenge LM Rebar Challenge SAK STACK Challenge 60 Days 30 Day TWEEN Challenge - 84 and 85mm SAKs Case XX 30 Day Challenge
                      1 Reply Last reply
                      • kwakster Offline
                        kwakster
                        Posts: 1,006
                        kwakster Offline
                        kwakster
                        wrote on last edited by
                        #5 Quote Reply

                          This was posted today on Bladeforums by Anne Reeve:

                          *This is a moment where CRK has to take a humble "cap in hand" and apologize for a failure of communication between our technical side and our customer service side. Yes, around mid-2013, the RC hardness on all the folding knives (Damascus excluded) was changed from 58-59 to 59-60. Our guarantee cards, brochure and website did not reflect that change. We are not happy about this lack of communication and are in the process of updating the relative published material.

                          Chris made the decision after reviewing the performance of S35VN at both hardnesses. He has always been a proponent of a slightly lower HRC to ensure shock absorbency and ease of sharpening. When he was convinced that blades at 59-60 would perform extremely well and meet all of his criteria, the change was gradually implemented. Bear in mind this is a possible spread of only 3% and a likely change of only 1% in the hardness and not a major change at all.

                          Anne*

                          1 Reply Last reply

                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                          With your input, this post could be even better 💗

                          Register Login

                          1. Home
                          2. Tool Talk
                          3. Edged Tools
                          4. Sebenza edges
                          Reply
                          • Reply as topic
                          Log in to reply
                          COMMUNITY LINKS
                          EDC-TV SAKWiki GearFeed SAKSelector
                          Operational Funds

                          Help us keep the Unworkable working!

                          Make A Donation
                          November Goal: $300.00
                          Due Date: Nov 30
                          Total Receipts: $0.00
                          Below Goal: $300.00
                          0% funded
                          • Login

                          • Don't have an account? Register

                          • Login or register to search.
                          • First post
                            Last post
                          0