Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Rossko's Modded Wave

Scheduled Pinned Locked Moved The Mod Squad
5 Posts 1 Posters 2.2k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Rossko's Modded Wave
Rossko's Modded Wave
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Rossko07 Offline
    Rossko07
    Posts: 321
    Rossko07 Offline
    Rossko07
    wrote on last edited by Rossko07
    Quote Reply

      Really excited to show you all. Here I have customised my wave. It's my second multitool mod but my first done on a full size multi.

      I have used four tools in total from a rebar for the build.

      1 - Rebar plier head
      2 - 3D Phillips
      3 - Small flat driver
      4 - Awl

      The tools I removed from the wave to enable these tools to fit were.

      1 - Large bit driver
      2 - Small bit driver
      3 - Scissors
      4 - Wave plier head

      The first step was removing the rebar plier head from said rebar. I was able to remove the plier head pins with just small vice grips & my blunt nose surge. All pretty straight forward here. Looks like it's just meant to be.

      Now onto the inside tools. First was removing the tools required from the rebar. These pins were quite hard to remove due to not having the correct tool and the pins being slightly recessed because of the rounded handles of the rebar. I got desperate & resorted to grinding one side of each pin set into a flat driver head and used such a tool to remove them. Unfortunate.

      3D Phillips added where the large bit driver was next to can opener.

      Small flat driver added where the small bit / eye glass driver was & awl added where scissors were.

      Without any modification to the tools or the multi itself there is no way to fully close the handles. First step without a doubt after fitting the tools is to carefully snap off both plier rests inside the handles. This is a must.

      The original tapered shape of the small flat driver was never going to remain. I don't know about you but I prefer it to be the same width of the entire piece so it was the first to be reprofiled into a more useful and appropriate design in my opinion. I have not altered the length just slimed down the top edge to run parallel with the bottom edge. It has great reach.

      I pondered for quite some time next and evaluated what more is involved. Even with this driver now slimed down the pliers were no closer to closing. Because of the length the tip of the driver was still touching the plier head. I really wanted to keep that driver as long as possible so I had to think of how another way.

      I started out with full intention of keeping the two blade safety retaining pins but with also wanting to keep the reprofiling of tools to a minimum & with the extra space taken up by the rebar plier head. I just found it impossible to keep them.

      Both were pulled out to increase the inside depth which would allow the tools to fold further in. Don't forget to flatten the rivet holding the inside tool lock spring. Great terminology there.

      Next I took the dremel to work again this time on the top edge of the awl. It also required slight reprofiling. But not much.

      Getting very close to fully closing now but I can see due to the locations I chose for my tools that the Phillips was touching the small flat driver when closing. Seen as I already reprofiled the flat driver I went to it again this time on the edge leading to the finger/nail nick to pull out the tool.

      No modification required on the Phillips or plier head at all. Most of the reprofiling of tools is necessary because the rebar plier head has square edges not rounded like the wave. This takes up precious room.

      Here are some pics of the inside tools while closed.

      Really happy with how it turned out being my second mod on a multi. I've learnt a lot. Hope this helps anyone looking to mod a wave. Cheers

      1 Reply Last reply
      • ducttapetech Offline
        ducttapetech
        Posts: 18,707
        ducttapetech Offline
        ducttapetech
        wrote on last edited by
        #1 Quote Reply

          Nice work man!

          That's us mobile

          1 Reply Last reply
          • zoidberg Offline
            zoidberg
            Posts: 38,161
            zoidberg Offline
            zoidberg
            wrote on last edited by
            #2 Quote Reply

              Looks good mate. :tu: :tu:

              1 Reply Last reply
              • SteveC Offline
                SteveC
                Global Moderators
                Posts: 73,535
                SteveC Offline
                SteveC
                Global Moderators
                wrote on last edited by
                #3 Quote Reply

                  :cheers:

                  1 Reply Last reply
                  • Rossko07 Offline
                    Rossko07
                    Posts: 321
                    Rossko07 Offline
                    Rossko07
                    wrote on last edited by
                    #4 Quote Reply

                      Thanks fellas! [emoji846]

                      1 Reply Last reply

                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                      With your input, this post could be even better 💗

                      Register Login

                      1. Home
                      2. Tool Talk
                      3. The Mod Squad
                      4. Rossko's Modded Wave
                      Reply
                      • Reply as topic
                      Log in to reply
                      COMMUNITY LINKS
                      EDC-TV SAKWiki GearFeed SAKSelector
                      Operational Funds

                      Help us keep the Unworkable working!

                      Make A Donation
                      November Goal: $300.00
                      Due Date: Nov 30
                      Total Receipts: $0.00
                      Below Goal: $300.00
                      0% funded
                      • Login

                      • Don't have an account? Register

                      • Login or register to search.
                      • First post
                        Last post
                      0