Evil's Quad Strop Mini.....
-
*Hey there, gang. It's that time of the year when things get crazy busy and I usually disappear until at least the fall, if not longer. In the spirit of trying to break that habit, I've been trying to devote a little time in between tasks to tinker. With that said, in reviewing my photos, please excuse my extremely dirty and greasy hands, lol. I worked on this project during breaks while working on a car.....
About this creation. In this modern day and age, rather than being content with killing time on my smartphone during spare time, etc., I often opt to sharpen knives. It's therapeutic to me in some weird, odd way. In actuality, I don't let my knives get dull to begin with. They're all sharp, it's a matter of how high of a level of sharpness they are at. At the first sign of dullness, I tend to them. I know, it's a bit of an obsessive habit. This little creation caters to that. There are a lot of competent portable sharpening systems out there, however, they often have grits that are way too rough for a near-sharp/sharp knife, rendering them inefficient to me. If I actually have to sharpen, I will do it properly and at home. There are also portable strops out there, typically single or dual faced and most do not have a way of protecting the strop surface, leaving you with having to find a way to cover it. This is especially an issue if loaded with a compound. My quad strop solves all of these issues for me by having exactly what I want and nothing that I don't. A system with four levels of stropping that also safely stores them for true portability.....
All stainless steel construction. Strop base is mahogany stained black. I make my own stropping tapes of various grits. If I hollow out the base, I can make use of that tiny real estate in the future if need be. Perhaps a ceramic rod or? The setup of grits/compound I'm going to go with for now will be perfect for a knife that is just starting to feel dull and bringing it back up to crazy sharp and then some. I may change the name and etch or engrave it on the back, we'll see.....
~ evil ~
*
Freehand mask in progress.....

Etching done.....

Lanyard/bolt side.....

Threaded side.....

Closer view of beveled holes that I created for both sides.....

Beveled bolt, holes drilled on both sides. D ring created and installed lanyard attached.....

Beveled nut installed. Rubber washer bonded in between. It applies counter-pressure when you tighten the bolt so it won't come loose unless you want it to.....

View of one side.....

View of other side.....

Locking pin removed.....

*Next step, push up and out through top. Here you can see how the leathers stay spaced away from the handle..... *

Pushed out partially.....

Fully removed.....

Flip 180 degrees and re-insert.....

Re-insert locking pin. Locked and loaded, it's ready to get down to business.....

View of one leather strop and stropping tape. I left a thin gap for the labels for ease of strop identification.....

View of the other two.....

Assembled view.....

Another view.....

And yet another.....

-
Love the design

-
wow.... -
Very pretty. Great idea.
Sent from my XT1563 using Tapatalk
-
What a wonderful creation!
What are the dimensions Evil?
-
That is way cool evil :o

-
you never fail to surprise and amaze.
very nice creation.

-
Thank you, ddogu.....

Thank you, Kampfer.....

*Thank you, JP..... *
@DaveK said:
What a wonderful creation! What are the dimensions Evil?Thank you, Dave. I made the length of the strops the bare minimum that would work efficiently for me. Being accustomed to the Lansky system, that length is an even four inches. Width is just a hair under one inch, close to twice the width of a Lansky stone. Overall length in open position is 9 inches, closed position measures 4.75 inches. Very EDC friendly size for me. Below is a comparison shot that I took today.....

Thank you, Poncho.....

@detron said:
you never fail to surprise and amaze. very nice creation.

Thank you, detron.....
I just set out to create things to suit my needs..... ;) -
Holy smokes! You've done it again. Always great seeing your work

:) -
@tattoosteve99 said:
Holy smokes! You've done it again. Always great seeing your work
:)Thank you, Steve.....
I've been putting it to such good use that I wonder why I didn't make it years ago..... -
well, your needs must be amazing, since they are the catalyst that jump starts your amazing products.
*Thank you, detron. It's more of a case of my needs never being satisfied with what I come across. Necessity is the mother of all invention, as they say.....
*Necessity is the mother of invention, but you are the Picasso of invention.
-
well, your needs must be amazing, since they are the catalyst that jump starts your amazing products.
*Thank you, detron. It's more of a case of my needs never being satisfied with what I come across. Necessity is the mother of all invention, as they say.....
*Necessity is the mother of invention, but you are the Picasso of invention.
Thank you, detron for the high praise. I am humbled.....

-
This strop gives me a idea. I'm going to make one for my sharpmaker.
-
@tattoosteve99 said:
This strop gives me a idea. I'm going to make one for my sharpmaker.Can't wait to see what you come up with...
I've been contemplating installing a suitable piece of ceramic rod within the strop base on this project. I do in fact have a pen sized field sharpener that I created but never thought to post on it since it is such a small, trivial project to me that I created on a whim. Be sure and post on your progress......
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login