Reshaping tools?
-
Good points! Really good points about the heat treatment thing. I was thinking about doing it to a Leatherman MT.
-
-
If it's a package opener your looking for you can modify the can opener into one and keep the saw. I did that on my Rebar and it works great.
</post/1041511>


-
-
-
Bump.
So I've done metal cutting and drilling but no real reshaping. Any tips? How do you get the profile angles so clean and uniform? Tools, techniques?
Thanks
-
So I've done metal cutting and drilling but no real reshaping. Any tips? How do you get the profile angles so clean and uniform? Tools, techniques?
Thanks
I usually try and get it as close as I can when grinding (a very steady hand helps a lot) ;) but I usually deburr and polish it a little with a diamond sharpening stone
That gives it a finish close to what I am going for as it smooths things out and makes all the edges smoother as well 
-
Also a Sharpie is a very good tool that will let you mark out what you want before you grind as well. I usually grind to the line and the if I have to go further I can
Because once you cut or grind it there is not getting back any of that material :D -
Measure and mark carefully first, then grind away. A steady hand and being patient helps. I suppose it depends on what tools you're using, and what metal you're cutting. I use files (metal and diamond), silicon carbide paper, a Dremel and a small belt sander, depending on what I'm doing. Usually finish with Scotchbrite.
-
Thanks you guys for the tips. I know it'll be trial and error, but hopefully these tips help curb the "error" a bit.
So I'm just looking to do the awl mod. Not sure which starting tool, but referencing Kampfers wave awl mod it turned out so good I wouldn't be able to decipher it from a new tool

So when you line up your cut, with the sharpie template. You cut it straight first (90*) then file the edge on. I'm p obably going to try on a flat or cap lifter so easily replaceable if I don't get the grind right. I'm not so concerned with creating the rough shape. It's he fine tuning after. And yes I'll use my dremel, and I do have access to files too.
Thanks again all!!
-
@kaput said:
Thanks you guys for the tips. I know it'll be trial and error, but hopefully these tips help curb the "error" a bit.So I'm just looking to do the awl mod. Not sure which starting tool, but referencing Kampfers wave awl mod it turned out so good I wouldn't be able to decipher it from a new tool

So when you line up your cut, with the sharpie template. You cut it straight first (90*) then file the edge on. I'm p obably going to try on a flat or cap lifter so easily replaceable if I don't get the grind right. I'm not so concerned with creating the rough shape. It's he fine tuning after. And yes I'll use my dremel, and I do have access to files too.
Thanks again all!!
Yes I would just cut the shape of it first and then sharpen it to the angle you want with a file and/or sharpening stone or diamond stone/file

-
This ^^^^
I used my dremmel, bench grinder and files when I reshaped my Rebar awl and also when I made the awl for my Pulse.
</post/1143411>
</post/1332115>
-
-
I use the grinder to grind out the shape I want then grind out a rouge edge at about 60*, finish it off with a stone.
-
I will use a grinder or cut off wheel for extensive reshaping, but usually I just use files and get good results. smurf files for the gross work and needle files for the finer details.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


I did that to mine as well after seeing yours