Modding a Charge AL
-
Hi,
I have a new Charge AL.
Two things are bugging me somewhat. First of all the scissors are tiny. Secondly although I could care less about the eyeglass tool, I would really like a second bit driver.
I know that the Charge ALX would give me the second bit driver but at the expense of the flat screwdriver which I wouldn't mind keeping, specifically as a mini pry bar.
My idea was the following.
-
Remove mini scissors and eyeglass tool and install second bit tool.
-
Remove serrated blade (which I have no use for anyway) and replace with Surge scissors.
Part 1 seems to be easy enough, there looks to be enough room there (I don't have a micrometer to check though). Part 2 is confusing me. The Surge scissors are intended to be on the other side of the tool to the serrated blade, they will be the wrong way round. Or am I getting confused and they would work fine? I realise I'd have to make a cutout in the scales to make them accessible.
Can you kind folk let me know if and where I'm going wrong with this idea?
Many thanks!
-
-
Might be easier to put SAK scissors in the outside. Or Flik scissors. Both will take very minor modding but the Surge scissors aren't that great IMO
-
@NKlamerus said:
Might be easier to put SAK scissors in the outside. Or Flik scissors. Both will take very minor modding but the Surge scissors aren't that great IMOI was looking for plug and play solutions as I have no ability to do any 'real' modding :) Thanks for the heads up about the surge scissors though!
-
I want to say Flik scissors are basically drop in.
-
Something like this /topic/41159
-
Part one will be fine.
Part two won't. The Surge scissors (which are great - don't listen to klamy) are too long.
The usual suspects are Wingman and SAK. Both options require some work.
I've only replaced the file or saw with the Wingman scissors. Would probably work replacing a blade but I haven't tried yet.
I would go with the SAK scissors.
-
@sLaughterMed said:
I want to say Flik scissors are basically drop in.They don't seem to be from the link above :) I have no ability to do any metal work I'm afraid.
What is involved with SAK scissors?
-
-
Good luck with the mods
Plenty of knowledgeable people here
Don't be afraid to ask any kind of question in regard to mods 
-
What is involved with SAK scissors?
Good link Zoid

-
Thank you for that link, how do those scissors compare to the built in one on the charge for cutting power? I have a Vic Outrider to hand (wife's), are those the same size scissors?
-
OK I see from here that they are:
I have to see if I can source these, if I take my wife's SAK apart she'll kill me, it was her 6 month anniversary present 15 years ago. It's still as solid as new. Really well made.
-
I don't yet have the tool to open up my Charge AL (on the way from Russia) so please be patient with me if this is a stupid question, would the scissors from the Charge fit in the slot where the serrated knife is? The hole diameter should be the same? I realise the nub would stick out a bit horizontally but there should be room for it in the cuttout. It's not going to be as big as the SAK scissors (though not that much smaller) but it will be direct plug and play.
-
@pomsbz said:
I don't yet have the tool to open up my Charge AL (on the way from Russia) so please be patient with me if this is a stupid question, would the scissors from the Charge fit in the slot where the serrated knife is? The hole diameter should be the same? I realise the nub would stick out a bit horizontally but there should be room for it in the cuttout. It's not going to be as big as the SAK scissors (though not that much smaller) but it will be direct plug and play.Never have seen anyone do that
Worth a shot though
I think most people want bigger scissors in that spot may be the reason (but it may not work and that be the reason I have never seen it :D ) Good luck on the mod and let us know how it goes
Also let us know if the scissors work or not so we will know what to tell people next time ;)Guess you are getting the tools from loki-mobile
I have those and the wrenches and they are superb 
-
@pomsbz said:
I don't yet have the tool to open up my Charge AL (on the way from Russia) so please be patient with me if this is a stupid question, would the scissors from the Charge fit in the slot where the serrated knife is? The hole diameter should be the same? I realise the nub would stick out a bit horizontally but there should be room for it in the cuttout. It's not going to be as big as the SAK scissors (though not that much smaller) but it will be direct plug and play.The scissors pivot and tang is smaller. Even if you enlarged the pivot I'm not sure you could get it to work with the liner lock. And if you could it still wouldn't be worth the effort.
I've used the Charge scissors for years. They might look small but they actually do work pretty well.
These days if a MT doesn't have scissors then I will carry a SwissCard and/or a Pioneer X with it.
Let me rephrase that.
I have a SwissCard (Nailcare) in my wallet and if I don't have my wallet on me then I'll have the Pioneer X in my pocket. -
I don't yet have the tool to open up my Charge AL (on the way from Russia) so please be patient with me if this is a stupid question, would the scissors from the Charge fit in the slot where the serrated knife is? The hole diameter should be the same? I realise the nub would stick out a bit horizontally but there should be room for it in the cuttout. It's not going to be as big as the SAK scissors (though not that much smaller) but it will be direct plug and play.
The scissors pivot and tang is smaller. Even if you enlarged the pivot I'm not sure you could get it to work with the liner lock. And if you could it still wouldn't be worth the effort.
I've used the Charge scissors for years. They might look small but they actually do work pretty well.
These days if a MT doesn't have scissors then I will carry a SwissCard and/or a Pioneer X with it.
Let me rephrase that.
I have a SwissCard (Nailcare) in my wallet and if I don't have my wallet on me then I'll have the Pioneer X in my pocket.I have a LM Style CS on my keychain already so it's not that crucial to have scissors at all. I have no need for the serrated blade however and was trying to do something useful with the space :)
-
If you could also do without the saw or file then for a very minimal effort you could go skinny.
@Breezy12 said:
I'm usually in my office, but I do spend a fair amount of time in the lab at work, so I modded this Skinny Charge to meet my office EDC needs. :D


I needed scissors because some of the electronic components in the lab come in packages that specifically say "OPEN WITH SCISSORS, DO NOT USE KNIFE OR RAZOR BLADE." I also wanted to have a 3/32" hex bit because I frequently need that size driver in the lab, but I can NEVER FIND IT because people don't put things away.

anyway, this modded ALX gives me everything I need at work and nothing that I don't... except for maybe the opener, but that comes in handy when I get home after a long day in the lab. :D actually, the wire stripper portion of the opener is actually very handy once you practice with it a bit.
oh, and I probably don't need the Rebar plier head either, but I was modding the Charge anyway, and I found a lightly used Rebar for pretty cheap on ebay, so....
-
@zoidberg said:
If you could also do without the saw or file then for a very minimal effort you could go skinny.I'm usually in my office, but I do spend a fair amount of time in the lab at work, so I modded this Skinny Charge to meet my office EDC needs. :D



I needed scissors because some of the electronic components in the lab come in packages that specifically say "OPEN WITH SCISSORS, DO NOT USE KNIFE OR RAZOR BLADE." I also wanted to have a 3/32" hex bit because I frequently need that size driver in the lab, but I can NEVER FIND IT because people don't put things away.

anyway, this modded ALX gives me everything I need at work and nothing that I don't... except for maybe the opener, but that comes in handy when I get home after a long day in the lab. :D actually, the wire stripper portion of the opener is actually very handy once you practice with it a bit.
oh, and I probably don't need the Rebar plier head either, but I was modding the Charge anyway, and I found a lightly used Rebar for pretty cheap on ebay, so....
Thank you, is it possible for a link where I could see the pics? I could do without the saw and serrated blade if that helps. :)
-
If you could also do without the saw or file then for a very minimal effort you could go skinny.
I'm usually in my office, but I do spend a fair amount of time in the lab at work, so I modded this Skinny Charge to meet my office EDC needs. :D



I needed scissors because some of the electronic components in the lab come in packages that specifically say "OPEN WITH SCISSORS, DO NOT USE KNIFE OR RAZOR BLADE." I also wanted to have a 3/32" hex bit because I frequently need that size driver in the lab, but I can NEVER FIND IT because people don't put things away.

anyway, this modded ALX gives me everything I need at work and nothing that I don't... except for maybe the opener, but that comes in handy when I get home after a long day in the lab. :D actually, the wire stripper portion of the opener is actually very handy once you practice with it a bit.
oh, and I probably don't need the Rebar plier head either, but I was modding the Charge anyway, and I found a lightly used Rebar for pretty cheap on ebay, so....
Thank you, is it possible for a link where I could see the pics? I could do without the saw and serrated blade if that helps. :)
You should be able to click on the (image removed from quote) part to show the pic, or the quote title for a link to the post.
Direct link to the post --> /post/827517
I made one from Charge parts a while ago and really liked it.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login