Leatherman(New Wave) adapted to regular 1/4" hex bits.
-
G'day all,
Posted this over on knifeforums, thought there might be some that would like to see it, that don't read over there. :)
I got to looking at the profile of the flat leatherman driver bits. They match regular 1/4" hex bits in width, and the angle to the corners. So, if you grind down two oposing flats on a hex drive bit, you can match the flat bits.
I picked up a 3"(2.75" gain) hex drive extention, figured since I was getting one for this, I'd get the one with the (ball detent type)lock on it to hold the bits.


Its just deep enough to hold and grip the flat bits too, not the lock, but the magnet holds them in. Would work for an extended reach with the flat bits.

5 minuites with the grinder, and I can now use any regular hex bit with my wave.




Just wish I'd thought of it before I got the flat bit kit. Its OK in a way, the flat bits are more compact to carry in their holders than the same variety/amount of drivers in 1/4" hex.
G.
-
Nice work!
The flat bits are neat for what they are, but I prefer the standard bits simply because you can get them anywhere. It's easier to get and carry exactly what you are likely to need, versus a cross section of the most common types. I imagine that rig would help out folks who deal with Torx or Robertson bits often.
Def
-
That's pretty cool - nice work!
I'm looking for a bit kit right now, as a matter of fact.
-
Good job Ice Tigre.
I've got one of the driver extensions Leatherman was giving out. (They talk of offering them as an accessory soon.) However, it uses a spring clip to retain the hex bit, not a magnet like yours. I'm not sure which style would be better. Both have their pros and cons.
-
Thanks All,
I'm actualy not sure why the magnet is there, 'cause the slide released ball-detent lock holds the bit in. For the regular bits, I would prefer to not have the magnet, so when the lock releases, they would fall free. But it is nice to have it for the flat bits, since the lock won't grip them.
I'm going to be trying to find an extention, with a (as compact as possible) ratchet on it, to convert the same way. Seems to be the next logical progression.
G.
-
Yah, we've been talking about multitool ratchet-drivers. That would be cool!
-
Tigre,
Did you ever find an extension with a ratchet built in. I've been looking for one & haven't found any - yet. Would be a great addition to the kit.
Tom
-
Nope never did... I quite looking when i lost my wave mid summer, and since i replaced it with a spirit... Come to think of it I have since lost track of that modded driver..
G.
-
I didn't kknow that leatherman was giving out an accessory like that.
-
They aren't giving them away anymore, they are for sale.
-
That my friend is a slick little unit ya got there. Looks very well made and very good in the fit dept.
-
How do you like a separate rachet tool? Otherwise, you may want to modify a racheting screwdriver (BIG PROJECT!).


-
I recently acquired a "L" (or "7" depending on which way you hold it) shaped hex bit driver to carry, It even has a pocket clip!
Anyway, I wonder how great bit adapters on multi tools are.
In many way they make sense, but there is still something odd.and having to add (and carry) an extra whatzit just adds more doubt.
Anyway, it seems nice what you have done, let us know how it stands up to some use.
-
Yah i can see a ton of wasted ratchets on my workbench now. And most likely a ton of band aids also.
-
I really think the idea of a ratchet implemented into an extension bit is a great idea. It would allow any bit driver to have a ratchet.
-
There are three possible ways to do it:
- Turning the handle (Red): You can use the screwdriver mechanism.
- Use the handle as a lever (Green and blue): You can shorten the handle of an L-shaped tool and weld an adapter to it.

-
Hi, guys, I've been reading here a few weeks and appreciate a lot of the stuff I've learned from y'all (thanks), but hadn't had a need to post anything until now. Just thought I'd pass on something I'd found regarding a "ratcheting" device for 1/4" bits that can be used with a Leatherman. A few weeks ago I had seen a bit holder ground down so it would fit the LM bit driver and decided to make one for myself as well. I did and it works great. Now I carry it along with several 1/4" bits so I can turn just about any screw or bolt/nut (up to 7/16") I come across.
Several months back I had purchased a Bit Dr. from Loggerhead Tools http://loggerheadtools.com/index.php?main_page=page&id=6&chapter=1. While I've not been impressed with the bits that were provided themselves (I've broken three already, with not a great deal of torque - although Loggerhead did send a free replacement set when I emailed them), it did also come with a so-called free-wheeling/ratcheting mechanism that I like very much. It takes a little getting used to, but once you do, it becomes very handy. The Bit Dr. also includes an extension that I carry along with the ratcheting mechanism. Both ratchet and extension have 1/4" male and female ends. These two pieces are all that I carry of the Bit Dr. now, but I find them very useful. It might be a little steep for just these two parts, but if you're really interested in a simple, small, effective ratcheting mechanism for driving 1/4" bits, it might be something worth considering.
Tim
-
That free-wheeling/ratcheting mechanism doohicky looks pretty clever. I've read the description a couple times, but I still don't quite understand how it works. Can you describe it a little better or post a couple pictures?
-
Yes, I'd like to know more about it as well!
Is the ratchet gizmo this little thing here? So it can be coupled into any standard 1/4" drive, converting it to ratchet action?

-
Well, after reading this thread, I decided to have a crack at this myself with a spare extension. Not having a grinder though, I had to hold the extension in the jaws of my Fuse whilst attacking it with the file on my
SurgeSURGE!!.Needless to say, it took a fair bit longer and I picked up a few war wounds along the way due to slippage of the file, but the end result was roughly the same. :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login