Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Fenix E05 problem

Scheduled Pinned Locked Moved Flashlight Forum
6 Posts 1 Posters 1.6k Views
  1. Home
  2. Non Tool Forum
  3. Flashlight Forum
  4. Fenix E05 problem
Fenix E05 problem
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Josh613 Offline
    Josh613
    Posts: 170
    Josh613 Offline
    Josh613
    wrote on last edited by
    Quote Reply

      Went to use my Fenix E05 in the garage and as I turned it on high mode it started flickering, almost as iif it cycling through the modes? Its never done this before so not sure why its doing it now. I tried a new battery and that fixed it for a short time then it happened again. Cleaned the contacts too and the thread on the twisty part. I bought this from Heinnie haynes in january 2015 I believe

      1 Reply Last reply
      • Blackbeard Offline
        Blackbeard
        Posts: 3,309
        Blackbeard Offline
        Blackbeard
        wrote on last edited by Blackbeard
        #1 Quote Reply

          not sure if you tried rubbing alcohol to clean contacts, but this also helps sometimes. also when you have tail cap off clean the bottom of the tube, the flat side that has exposed aluminum.

          what type of battery were you using?

          1 Reply Last reply
          • AimlessWanderer Offline
            AimlessWanderer
            Posts: 17,518
            AimlessWanderer Offline
            AimlessWanderer
            wrote on last edited by
            #2 Quote Reply

              @Blackbeard said:
              not sure if you tried rubbing alcohol to clean contacts, but this also helps sometimes. also when you have tail cap off clean the bottom of the tube, the flat side that has exposed aluminum.

              what type of battery were you using?

              Yup, this has worked on a few of my lights. A good clean up with alcohol, dry thoroughly, and use a silicone lube on threads. If a new battery cured this for a while, it reinforces it in my mind. The slightly higher voltage of a new battery can overcome a minor connection issue, then revert to fault as the voltage backs off a little in my experience

              1 Reply Last reply
              • Josh613 Offline
                Josh613
                Posts: 170
                Josh613 Offline
                Josh613
                wrote on last edited by
                #3 Quote Reply

                  A energizer, the tail cap doesn't come off

                  1 Reply Last reply
                  • TazzieRob Offline
                    TazzieRob
                    Posts: 1,493
                    TazzieRob Offline
                    TazzieRob
                    wrote on last edited by
                    #4 Quote Reply

                      By Tail cap you could consider this the main body or battery compartment for the E05.

                      If yoy cleaned the contacts inside the head, did you also clean the surface of the body where is makes with the two negative contacts in the head? Make sure you don't have any lubricant on the contact points.

                      Your old battery hasn't leaked and caused some corrosion inside the body at the spring?

                      I think if the battery is low, it will just stay at the same as medium when put on high, and if it is too low then low mode is all you get until it stops altogether

                      1 Reply Last reply
                      • sergemaster Offline
                        sergemaster
                        Posts: 1,058
                        sergemaster Offline
                        sergemaster
                        wrote on last edited by
                        #5 Quote Reply

                          Amici,
                          On a positive note the Fenix E05 is relatively inexpensive (in the US), so if this one turns out to be a lemon, a replacement can be picked up relatively on the cheap.. You could also reach out to the vendor directly, and see if they would exchange the broken bugger for a working replacement.

                          I've had no issues getting a replacement light directly from Maglite as well as Eagtac when something "goofy" caused those lights to fail in explicitly.

                          Cheers,
                          Serge

                          1 Reply Last reply

                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                          With your input, this post could be even better 💗

                          Register Login

                          1. Home
                          2. Non Tool Forum
                          3. Flashlight Forum
                          4. Fenix E05 problem
                          Reply
                          • Reply as topic
                          Log in to reply
                          COMMUNITY LINKS
                          EDC-TV SAKWiki GearFeed SAKSelector
                          Operational Funds

                          Help us keep the Unworkable working!

                          Make A Donation
                          November Goal: $300.00
                          Due Date: Nov 30
                          Total Receipts: $0.00
                          Below Goal: $300.00
                          0% funded
                          • Login

                          • Don't have an account? Register

                          • Login or register to search.
                          • First post
                            Last post
                          0