Fixing bent blades
-
I searched the forum and google, but got so many results unrelated to fixing bent blades, I apologise in advance if there's some old thread I should be resurrecting instead of starting one.
I get pretty much all my SAKs used and usually online. Some people have no idea about things and photos are often unclear, so I've ended up with several knives with bent tips.
Generally the bend seems to be about 8 to 15 mm back from the tip, so I don't mean the very tip. I get the feeling most of these are from awesome geniuses who decided to use the blade as a pry tool.

I did find a few threads elsewhere where someone had asked how to fix these. "Take it to a professional knife repair shop" to "boil it then hit a hammer against it" have been some of the answers.
So I'm not trusting what I'm reading. Also I figure you experts know more about how Victorinox's blades specifically respond to the various fixes.
I have tried to fix a couple. I tried simply pressung the tip against a hard surface with a lot of force. The blade returns to the curved state when I release it. I have a bench vise here with anvil surface on it , so I could clamp it in there to bend it or hammer it against the "anvil" section (whatever the name for that flat section on the vice is called)
The thing is I wanna be able to control where the bend is, so I don't just put another bend in it in the opposite direction.
Most of them are 91s but I also have a bent Pioneer and those blades are thicker...
I also don't understand tempering and if there's any real advtange to trying to heat a blade fist, plus I wouldn't know how to "re-temper" it afterwards. I do have a small torch here.
So, probably a repeat question, but how are you guys fixing bent blades? (Twisted blades I don't even want to bother with)
-
They will not all be repairable by straightening, and the success levels will vary. Having said that, here's my thoughts on how best to try and reclaim a blade that's been damaged this way......
Slow clamping and releasing will only make a difference to the most distorted blades, and there will always be an element of springback. This can be minimised through impact, though may lead to cracking/fracture. Laying the blade on a smooth anvil or stidy with the tip and the blade the other side of the bend as contact points, and the bend itself uppermost, give the crest of the bend a good smack with a hammer. This should "coin" it straighter and eliminate springback. Do not expect perfect straightness. Wear sturdy gloves and eye protection. Applying heat to the blade will screw it up even more.
After straightening, check for cracks. With power abrasives or files/stones, remove any residual damage and straighten up the edge, removing any cracks or chips as you do. A cracked blade is potentially unsafe, so grind it all away now while you still have your gloves and eye protection. Remember to keep the blade cool. Applying heat to the blade will screw it up even more at this stage too. Reshaping the tip can be done by dropping the spine of the blade. It might end up with a slightly clipped point, but that shouldn't be a problem. Be sure also to close the blade and make sure the point of the tip is seated below the scales so it doesn't catch on clothing or skin.
-
I have had luck straightening a few by both carefully hammering with a nylon tipped hammer or placing the tip in a vise and carefully bending. If you have a vise with jaw protectors on it you can loosen one side to make a small gap that you fit the tip of the knife in and then carefully apply pressure on the tip.
<a href="http://s86.photobucket.com/user/asc67/media/DSC03337_zpsqzfpj3zz.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i86.photobucket.com/albums/k115/asc67/DSC03337_zpsqzfpj3zz.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
<a href="http://s86.photobucket.com/user/asc67/media/DSC03354_zpsjr6iedqz.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://i86.photobucket.com/albums/k115/asc67/DSC03354_zpsjr6iedqz.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
-
Seems as though Trad and Steve have said basically everything I was going to so no need to repeat
I hope this info helps and let us know how it goes

-
Thanks a million for the in-depth advice. Putting it in the crack between the jaw and jaw protector is something I never would have thought of.
I do have 1 vise like that but the protectors are some type of soft nylon or teflon.
I'll give it a go!

-
Just go slowly and carefully and let us know how it works out

-
I am a Brass Hammer and Anvil user. :Dbut also have used the Vise trick too.

Both work IMPO.
It is all bout making sure the blade is FLAT AGAINST your Vise walls or flat on the Anvil.
IMPO , If you dont have it flat and smack or press it just right ..... SNAP , off the tip comes! >:( :D

-
Good luck, I have snapped 2 now.

ATTENTION PEOPLE! A knife blade is NOT a pry tool!!!

-
@twiliter said:
Good luck, I have snapped 2 now.
ATTENTION PEOPLE! A knife blade is NOT a pry tool!!!

On SAKs. I'm 2 for 2 as well.....Wengers especially, are hard as hell.
Had good success on other types/steels using a wooden picnic table...
The small gap between the boards, and it being wood, is very forgiving on the blade and has let me "finesse" some blades back to true.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login