Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Need modding help

Scheduled Pinned Locked Moved The Mod Squad
4 Posts 1 Posters 1.2k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Need modding help
Need modding help
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • NetsNJ Offline
    NetsNJ
    Posts: 676
    NetsNJ Offline
    NetsNJ
    wrote on last edited by
    Quote Reply

      (Moderators, if this is in the wrong forum, please move.)

      So I have a Victorinox s54 where the plastic ruler is clean snapped off broken off. I'd like to have the three backsprings that support this tool removed for a slimmer knife. So it would just be a matter of drilling out the pins, removing those backsprings, trimming the pins, putting the bushings back on, and peening the pins. So no grinding or new parts necessary. Unfortunately, I lack the tools or experience to do this successfully. Would anyone here be willing to do the mod if I sent them the knife? For what price?

      Thanks!

      Example:

      1 Reply Last reply
      • Poncho65 Offline
        Poncho65
        Global Moderators
        Posts: 88,523
        Poncho65 Offline
        Poncho65
        Global Moderators
        wrote on last edited by
        #1 Quote Reply

          I am not much help with this but I do hope you find someone to either help you do it step by step or can do this for you :salute: Perhaps contact Syph007 and he can either point you in the right direction or be able to do the labor part for you :tu: There are several other modders here as well and they might also be able to help you :cheers: :cheers:

          Good luck with the endevour :tu:

          1 Reply Last reply
          • NetsNJ Offline
            NetsNJ
            Posts: 676
            NetsNJ Offline
            NetsNJ
            wrote on last edited by
            #2 Quote Reply

              ^ Thanks!

              The knife in question

              1 Reply Last reply
              • sLaughterMed Offline
                sLaughterMed
                Posts: 3,450
                sLaughterMed Offline
                sLaughterMed
                wrote on last edited by
                #3 Quote Reply

                  If you own a cordless drill, a couple clamps, a hammer and a ~8 ounce ball peen hammer (Tekton ones are $10 on Amazon) you can absolutely do this job yourself.Just gently pop the scales off with a small SAK blade, drill the pins out with a 3/32" drill bit (a 1/16" will work too, just have to drill deeper) until you can pop/pry the bushings off (pliers will work, just be careful with the lip of the bushing). Take out the layers preceding the springs, then the offending springs themselves. File down the pins until they are flat, then round the corners a bit and reassemble. If you have a lot of extra pin, snip it off with some dykes, and refile.You should have about 3/32" of pin left above the bushings. Next, use your clamps to clamp your hammer (not the ball peen) to a sturdy flat surface (I use our dining room table). This is your anvil. Hold the SAK in such a way that the pin you are going to peen rests directly on the hammer, with the unpeened pin facing upward. Using the ball part of the hammer (never the flat) use medium force to peen the pin (this will take a few minutes). Make sure to check the tightness of the pins every few swings, as it is easy to over-peen and make your SAK a nail biter. Once you've done all the pins, use pliers to twist a tool on each pin back and forth, to ensure you have seated the bushings fully. Repeat as necessary. Once you are done, put the scales back on, and you are finished!

                  Or, if you don't mind me taking forever to get around to it, I'll do it for you :)

                  1 Reply Last reply

                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                  With your input, this post could be even better 💗

                  Register Login

                  1. Home
                  2. Tool Talk
                  3. The Mod Squad
                  4. Need modding help
                  Reply
                  • Reply as topic
                  Log in to reply
                  COMMUNITY LINKS
                  EDC-TV SAKWiki GearFeed SAKSelector
                  Operational Funds

                  Help us keep the Unworkable working!

                  Make A Donation
                  November Goal: $300.00
                  Due Date: Nov 30
                  Total Receipts: $0.00
                  Below Goal: $300.00
                  0% funded
                  • Login

                  • Don't have an account? Register

                  • Login or register to search.
                  • First post
                    Last post
                  0