Where do you source 1/4 bits?
-
I'm sure I'm not alone when I say there are variances in the bits I've owned over the years. Some don't fit right, others are soft and smear when used. I really like the ones that came with my Victorinox ratchet, they seem to be a higher quality then others I've owned. Alas, I've lost a few and am trying to restock. Where do you guys get "good" bits?
Sent from my iPhone using Tapatalk
-
From my employer...
Lol!
Seriously though, I've bought a set from Bosch for the mini bit ratchet that came with it and so far they're holding up quite well.
Bought it at a well known DIY store over here. -
I think I saw some of those vic bits on ebay a few hours ago
-
I also trust Bosch.
Their long bits are the best I have found out. -
I buy bits whenever I see them and/or need them. I have cheapo bits and I have good bits from Bosch, Stanley, Rigid, Mastercraft and a few others. There are indeed some variances in quality, and many bits have found themselves flung across the room as a result, but then they are so cheap and plentiful that I generally consider them expendable.

Def
-
Thanks guys. I found a set on eBay from Victorinox. Ive tried the Irwin ones, as well as the Bosch, but none have ever held up or gripped as well as the vic ones. Thanks again!
Sent from my iPhone using Tapatalk
-
I love my Vic and SOG bits, or the old LM Tool adaptor's bits over most others and use them 90% of the time. Other 10% of the use is from LM's flat bits

-
Good quality bits I buy online from tool supply sites. Though the last set I got were from work
Most of the time for light to medium duty use I just use the leatherman flat bits I carry with me, for anything more robust I'd get a proper tool for the job, either a dedicated screwdriver or a driver for the quality hex bits.
-
@Kevin Davey said:
Good quality bits I buy online from tool supply sites. Though the last set I got were from workMost of the time for light to medium duty use I just use the leatherman flat bits I carry with me, for anything more robust I'd get a proper tool for the job, either a dedicated screwdriver or a driver for the quality hex bits.
Can you give me a link perhaps? I really haven't had any luck with the flat bits, they twist and smear to easily for me. Once I paired the VIC ratchet with all my EDC setups I never looked back. I even swapped the bit exchanger from my surge for a 3D Phillips so I could use the 1/4 inch bit exchanger instead. Thanks!
Sent from my iPhone using Tapatalk
-
You can't go wrong with impact ready bits, they can take a lot of stick. Not sure where in the world you are so here's a link for a deWalt set on amazon
-
I carry a Chapman 1316 set instead of an MT that takes bits. It is 1/4 drive. My grandfather has a number of these sets that he'd broken the "midget" or ratchet on that I get the bits from if I lose them.
https://chapmanmfg.com/collections/all-tools/products/1316-all-purpose-set
As for the 1/4 bits I use, just about everywhere. The tamperproof Torx I have are Irwin, sold as Lowe's Kobalt. As are most of what I have.
-
I do not use bits often. Most of the Torx drivers or bits, either purchased by my employer or supplied with cutting tools we bought, are Sanvik or Wiha. The security torx bits I bought to disassemble my LM tools are Wiha, a German brand. Expensive but well made with high precision. They outlast the same size bits from an American-made, budget bit sets. If you value your time, your screws, and your sanity, buy quality tools for the jobs.
-
+1 after breaking more bits and knackering more screws than I care to remember I buy Wera Impaktor bits now. A bit expensive but I haven't broken one yet

-
I buy Wera and Wiha bits when available locally, and otherwise Bosch.
Cheap bits tend to slip, bend or break with my 10 thumbs and lack of finesse, so I gravitate towards tools that can take abuse in the stride.
-Tom -
Thanks for all the great info guys!
Sent from my iPhone using Tapatalk
-
I use DeWalt and Kobalt (Lowes house brand) bits.
-
I just used 5-point Wera bits to disassemble some old Leatherman tools last night (http://www.micro-tools.com/product.htm?pid=132057&cat=15545). I was able to get the screws out without heating up the locktite. The fit in both the 1/4" driver and the screw is perfect.
Those maintenance guys at my work also use German-made screwdrivers and hex keys (Allen wrenches). They laughed at Crapman stuffs.
-
I get PB SwissTools bit :D... I can buy them individually at the local hardware store.
-
Gunsmithing screwdriver bits fit screws very well you can find them on Amazon. The higher priced sets hold up better. I bought a single action Colt set of bits years ago from Brownells they are holding up well.http://www.brownells.com/gunsmith-tools-supplies/general-gunsmith-tools/screwdrivers-sets/magna-tip-bits/magna-tip-bits-prod501.aspx
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login