Dismantling Leatherman Tools(Winning The War on Knurled Knobs)
-
Seeing Kwakster's specialized tools got me thinking
. Sponny's (spoonrobot) excellent post/topic/4655 and Goldy(Goldmeister) terrific ideas in the same post proved the inspiration to me doing the modified Spoony socket. Instead of using the whack the bejeebers out of the socket with a hammer to imprint the knurled profile into the socket I have modified the Spoon process by using a vice to push the socket over the knurled fastener and thus create my own Leatherman like socket.
To start with you need to buy a CHEAP socket set ideally a combined Metric/Imperial set.The cheap ones tend to have odd ball sizing like 5.5 & 6.5mm sockets which are ideal. My set cost $8Aus from a Automotive parts/miscellaneous junk chain store called Super Cheap.
[(http://i291.photobucket.com/albums/ll287/multimat426/multitools/ac9c9c44.jpg)]
](http://
I also put some tape on the vices face that was going against the MT. I then lined the MT up so that the knurled fastener I wanted to get a imprint of was bang in the middle of the vice , I then secured the MT in this position with duct tape , that gives you a free hand to position the socket and turn the vice at the same time. Like this, sorry this pic is not the best.
[(http://i291.photobucket.com/albums/ll287/multimat426/multitools/0cedafb9.jpg)]
](http://
It is important to get the initial line up as close as possible before taking the leap and tightening the vice up. I used my Fuse mostly + my PST & Micra for the process . I was surprised at the amount of force required to consummate the union. I could not detect any harm to the MT's post squeezing but I guess it is possible if you go nuts(I just went partially nuts :D) Here is the loving couple.
[(http://i291.photobucket.com/albums/ll287/multimat426/multitools/2e3fac83.jpg)]
](http://
Here is one of the two Micra sockets.
[(http://i291.photobucket.com/albums/ll287/multimat426/multitools/1123ee29.jpg)]
](http://
OK. THE PROS ; they work , my LM's will not get damaged(can happen with vice grips) , I do not need to wait for Kwakster's tools to make it to OZ, cheap to make .
THE CONS ; If you use good quality sockets (ie hard) you can Roger the fastener and not have a mod tool.I tried a Sidecrome(Australian tool making institution) & this happened
[(http://i291.photobucket.com/albums/ll287/multimat426/multitools/12619a69.jpg)]
](http://
In my quest to make a spanner like tool I went a bit silly and my vice went, Snap , Crackle & Fu#ked :- :(
[(http://i291.photobucket.com/albums/ll287/multimat426/multitools/4c11f898.jpg)]
I tried Spoony method & just could not get the socket to sit when hitting it with the hammer . I tried making the socket red hot & hitting it with a hammer & no luck.I tried using a G clamp with marginal success(socket tended to slip & then spin >:( ). This method does work ,I would be interested to hear how people go if they chose to give this way a go. Thanks to Spoonrobot & Goldmeister for their good ideas. -
Excellent!

-
Great tutorial mate

-
Good work Mat - I must have a go at this sometime.
-
You know, bashing the knurled heads into a regular hex shape isn't such a bad idea either...
-
Sidecrome(Australian tool making institution)
Until they were bought out by Stanley and they started making tools in taiwan.
I'm off to by a SupaTool set from the auto store!
-
Great job MM
The pics look of fine quality to me ;) I am gonna have to get some cheap bit and try this myself :o :D :D :D -
Alright, lets see what type of odd fastener Leatherman comes out with next to thwart us!
This thread makes me wish I didn't sell my Blast and Kick :(
-
-
Add it , I have found if the knurled imprint is not perfect you can file the socket down & give it another go(Surge's file worked well). It is easy to go too quick and bugger it up . So the best way is go slow :D.
PS ideas on getting the broken bolt shafts out of my vice so I can put new bolts in. I was thinking of using my dad's drill press & using something like Eazy outs? I have not used this before any tips ? It is funny I have had that vice for 3 years & not really used it much until I needed to make these sockets & decided to finally mount it properly under a week ago ::) :D
-
If you need soft sockets, heat one up till magnet doesn't stick then throw it in some non-flammable insulator and let it cool down slowly.
-
@MultiMat said:
Add it , I have found if the knurled imprint is not perfect you can file the socket down & give it another go(Surge's file worked well). It is easy to go too quick and bugger it up . So the best way is go slow :D.PS ideas on getting the broken bolt shafts out of my vice so I can put new bolts in. I was thinking of using my dad's drill press & using something like Eazy outs? I have not used this before any tips ? It is funny I have had that vice for 3 years & not really used it much until I needed to make these sockets & decided to finally mount it properly under a week ago ::) :D
You'll be needing to use eazy outs on that vice Mat. Generally they are sold as a 3-piece or 5-piece set. Even better would be if you could borrow a set from someone, as you are unlikely to use them very often.
-
Thanks Bob , my research tells me cheap stud removers are not great for the job & like you said I probably will not need the kit ever again so buying a expensive kit not good sense . Now who do I know who might have some

-
THREAD NECRO!
this is very nice
-
I remember reading this awhile back. Useful information.
-
I bought 2 sets of "testing" sockets. these are the pinnacle Dollar Tree tools

if these are not soft enough, then I do not know what is. it was $1.00


-
Good luck mate :D :D
-
I like the marred fasteners, it gives it character. Really though, I should try and make some of these.
-
I am just too cheap to buy the Vampliers for the cost of two of those, I could buy another MT or SAK ::)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login