Plier cutting test
-
There was this issue with cutting braided steel wire in another recent post, which for various reasons is a bit interesting to me. So I figured I'd give some normal pliers and multi-tools a go at that.
While I'm going at it anyway I figure I might as well give some other materials a go too? So the plan has been extended to include not only the galvanized multi-strand wire thing, but also paper strips, stainless steel tig welding rod, steel wire tig welding rod, some small carpenter nails, and some annoyingly flexible plastic filament for 3D printing.
I plan to apply pressure gradually using one hand exactly once and to my limit if needed. (There will be no tricks like reversing grip, knocking, chewing, hammering, cooling or work hardening).
The material selection would likely make for some difference of results between the pliers. If anyone else have suggestions for a relevant material to add into the mix I'm open to suggestions. (I reckon all will cut normal electric copper cables so I wont even bother with that).
-
Can't wait for the results

-
<a href="http://imgur.com/y3eHDCV" target="_blank" rel="noopener noreferrer"><img src="http://i.imgur.com/y3eHDCV.gif" alt="banner" style="max-width: 100%; height: auto;" /></a>
-
Ok, tests done - lots of them. This turned out to be a more diverse result than I had imagined. There were also many casualties among the multi-tools plier edges. Not even the cheap normal pliers got damaged, so that was surprising and disappointing. (Not to mention expensive..)
This will be very picture heavy so will take some time to chop down to web size. If I get this right there is a 4Mb 4 picture max per post limit for attachments here on the forum? Anyone have any recommendations of where to put and link to the rest?
First off the materials that got tested: From top left to right: 17-4 Stainless steel flat spring (8.5x0.9mm), 316L Stainless steel flat spring (8.5x0.9mm), square electroplated nails (1.8mm), steel tig welding rod (3mm), aluminium tig welding rod (2?mm), 316 stainless steel tig welding rod (1.5?mm), galvanzied steel lawnmover control wire (2mm), paper strips, soft PLA 3D printing filament (3mm), and some decent sized ziplock thingy.
Then we have the normal pliers and some less normal ones. From left upwards to bottom right: Some old sheep scissor (or whatever), a fencing tool, Knipex bolt end cutter, Knipex small universal plier, old Knipex cutter (forgot to test), cheapo something nose plier, some old Swedish electrical end cutter, some old Swedish electrical side cutter, Teng Tools Universal plier, cheapo something Universal plier, Knipex universal plier, Wiha electrical side cutter, Ergo side cutter.
The multitools I could find laying around. From top left to bottom right: IDL T10, cheap unbranded Chinese one, Henstrong, Cima (?), some often rebranded chinese one, some other often rebranded chinese one, another Cima (not tested - no plier or scissors...), Ruiss something something, Ruiss something else, Gerber Dime, Wenger Mechanic (?), Leatherman Juice , Leatherman Wave, SOG Power access (?), Ganzo 300 something (302?)
The test procedure was easy enough. Grip with padded work glove at the far end of the plier. Then a single go with gradually increasing pressure. An exception for the ziplock for the pliers that did cut but simply didn't have wide enough jaws to do all at once - there I would cut again to finish off.




-
Some results:
Tool Flat 17-4 Flat 316 Wire Rod 316 Rod Alu Rod Steel Paper Ziptie Nail Filament Damaged? Knipex end bolt cutter Y Y Y Y Y Y Y Y Y Y Bad ass scissor Y Y Y Y Y Y Wiha Electric side cutter Y Y Y Y Y Y Y Ergo side cutter Y Y Y Y Y Y Y Y Cheap nose plier Y Y Y Y Fencing tool Y Y Y Knipex small universal Y Y Y Y Y Y Y Knipex universal Y Y Y Y Y Y Old Swedish end cutter Y Y Y Y Y Y Old Swedish side cutter Y Y Y Cheap unviersal Y Y Y Teng tools universal Y Y Y Y -
~~I think the formatting failed, maybe you are missing a slash or something? ~~
Wow!

-
Umm... Are the Y's lined up right?
-
Ok, I've messed with the HTML and at least it should be readable?
-
It appears to say that no tools were damaged
-
Yes, that would be right - all the normal pliers were undamaged.
Multi tool results though... :-[
Tool Flat 17-4 Flat 316 Wire Rod 316 Rod Alu Rod Steel Paper Ziptie Nail Filament Damaged? Leatherman Wave Y Y Y Y Y Y Y Ganzo something Y Y Y Y Y SOG Y Y Y Y Y Y Leatherman Juice Y Y Y Y Y Y Henstrong Y Y Wenger Mechanic Y Y Y Cima blue Y Y Y Y Y Y Chinese large head Chinese small head Y Unknown skeleton sides Y Y Y Y Y Small Ruiss Y Medium Ruiss Y Y Y Y Y Gerber Dime IDL T10 Y Y Y -
There were some clearly distinct failure modes:
Lack of leverage and they had no chance at the flat stainless steel ones or the steel rod. Actually I stopped trying the flat ones after a while - apart from the Knipex end cutter there was hardly a scratch to be seen.
Lack of precision would cause failure at paper, zip tie, filament or wire.
Possible lack of hardness also caused failure with stainless steel and galvanized wire samples. Combine that with long enough handles to get leverage and the tools simply turned suicidal. Neither stainless 316 or that galvanized wire should be particularly hard, so that was quite surprising.
Another way to fail with the stainless rod, wire, zip tie and filament was for the jaws to actually spread apart sideways so there opened up a gap in between the edges. This happened a lot with the small narrow multitools.
Biggest positive surprises here were the little Knipex universal, medium sized Ruiss and the Juice. For the size they did a lot, and they didn't get damaged trying at harder stuff either.
Now this was of course only a single sample of each tool so milages might vary. And many would have been able to chew through some of the stuff if I had pumped the handles. Applying greater pressure using a hold, reversing grip or otherwise would also have helped. But for what it was, one hand pressure, it is an indication of what to expect - at least in the more general big picture view of things.
-
Some more pictures...
The Knipex end cutter was the only one to do it all. And fairly easy at that too. The small Knipex universal did a lot for its size. The Leatherman Wave got damaged on the 316 rod and the nail. And the story was pretty much the same for the Ganzo.




-
More pictures...
The Juice was the only multi-tool to cut the wire. (Before I started I assumed all the multi-tools except the small ones would do that actually). The Wenger scissor did surprisingly well with that zip tie. The medium Ruiss is quite the package for its size. And finally the IDL was the smallest of the bunch but still cut some at least.




-
Thanks! I love tests like these.

-
A few more for now.
The old worn rusty scissor did well. I guess bulk does count for something. The Wiha side cutter did its stuff easily enough except for the larger steel stuff. The Ergo side cutter did all but the flat steel springs, and was by that on a second place performance wise. And then we have the Gerber Dime which did exactly as the picture shows - no cut of nothing. (To be fair, if I've used the scissors instead it would have taken the paper and possibly the soft filament).




-
The small electric side cutter wasn't the best sample as the edge was a bit rusty. Still precise enough to do paper, and squeeze of that aluminium. The small end cutter was in better shape and did very well for its size. The blue Cima was a positive surprise up to the point that it got damaged. The one with the large pop-out plier head, an often rebranded design, proved to be anything but usable. It cut nothing; lack of leverage and lack of precision also meant that any lack of sturdiness or hardness couldn't even be discovered.




-
The previous version of that pop-out head tool did a tiny bit better - it cut off the aluminium. Basically the same issues though. The small unbranded skeleton thingy did quite well actually. Borderline damage though. The small Ruiss had problems keeping the edges next to each other and only ended up doing aluminium. And the SOG was another downer for the multi-tools with proper sized handles. Like the Wave and Ganzo it damaged itself during cutting.




-
Very valuable, thank you!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

