Executive Scales falling off
-
I got an Victorniox Executive in a trade and the scales where the toothpick and the tweezer's are coming out do not stay flush, I tried taking them off and re-attaching as well as using a set of plier to put them back on and probably did more damage because one won’t even stay on now. I tried reaching out to Victorinox and they are asking for me to mail in a $5 dollar bill yada yada yada, they might wave the fee if I show them a recent receipt which I don't have. How do I get the scales to stay on? One of them unfortunately is probably damaged beyond repair, I guess I can try to superglue them. Kinda bumbed as I really like having this tool.
-
Sorry for your troubles, mate.
I think scales can't be re-installed once they've been taken off. I've heard of some people warming the scales before taking them off and then reusing them, but I've never seen that. If you didn't warm the scales before removing them, they are probably dysfunctional now.
I think your best bet is to send the knife in or buy a new set of scales and replace the now dysfunctional ones.
Best wishes!
-
You can try glueing them. :)
-
I've never heard of Vic charging people for warranty work, unless it's a shipping/handling fee

-
Yeah they want a $5 shipping and handling fee
Sent from my iPhone using Tapatalk
-
-
Once epoxied, always epoxied.
If you go the glue route, be careful not to obstruct the channels for the T&T with glue.
-
$5? What are you waiting for?

-
@hiraethus said:
$5? What are you waiting for?
I can get a new recruit for $13 bucks. If I put the $5 in the letter are they going to "loose" it? pluss I have to apply shipping costs. Its not a big deal but is it really worth it when I can just use epoxy?
Sent from my iPhone using Tapatalk
-
Not if you want a Recruit, no.
-
$5? What are you waiting for?

I can get a new recruit for $13 bucks. If I put the $5 in the letter are they going to "loose" it? pluss I have to apply shipping costs. Its not a big deal but is it really worth it when I can just use epoxy?
Sent from my iPhone using Tapatalk
Epoxy is a good call too! Just don't put on too much and gunk up the tools or the t&t slots.
-
Thanks
-
$5? What are you waiting for?

I can get a new recruit for $13 bucks. If I put the $5 in the letter are they going to "loose" it? pluss I have to apply shipping costs. Its not a big deal but is it really worth it when I can just use epoxy?
Sent from my iPhone using Tapatalk
If you use epoxy, make sure you only apply a small amount in each of the 4 rivet holes on the scales. It will be more than enough to hold securely and won't give you too much trouble to take them off if you decide to change them later
-
$5? What are you waiting for?

I can get a new recruit for $13 bucks. If I put the $5 in the letter are they going to "loose" it? pluss I have to apply shipping costs. Its not a big deal but is it really worth it when I can just use epoxy?
Sent from my iPhone using Tapatalk
If you use epoxy, make sure you only apply a small amount in each of the 4 rivet holes on the scales. It will be more than enough to hold securely and won't give you too much trouble to take them off if you decide to change them later
Thanks that will be my project tonight
Sent from my iPhone using Tapatalk
-
Super glue is a bad bet. It is way too brittle. The scales need to flex ever so slightly when the t&t are inserted and removed, and this action will break the super glue. Also given it's viscosity it can smurf up the pivots.
I use goop glue for sale scales and it works perfectly.
-
Is the $5 for shipping within the US?
-
@NetsNJ said:
Super glue is a bad bet. It is way too brittle. The scales need to flex ever so slightly when the t&t are inserted and removed, and this action will break the super glue. Also given it's viscosity it can smurf up the pivots.I use goop glue for sale scales and it works perfectly.
What about epoxy? Any experience with using that on SAK scales?
-
Not personally, but I know others have. I imagine it is fine.
-
Super glue is a bad bet. It is way too brittle. The scales need to flex ever so slightly when the t&t are inserted and removed, and this action will break the super glue. Also given it's viscosity it can smurf up the pivots.
I use goop glue for sale scales and it works perfectly.
What about epoxy? Any experience with using that on SAK scales?
I've glued two vintage solid scales with epoxy (Araldite) with only one tiny amount on the scale rivet holes and it worked great

The idea is not to actually glue the whole contact surface of the scale to the liners (that would be silly IMHO...
), it's more like "replacing" the amount of cellidor removed (ripped) from the holes by the bushings when taking the scale off, that makes the scales not sit tightly any more when putting them back vs to when they where new. That small amount of epoxy will fill the lack of material and harden but yet retain great elasticity while also being adhesive to the rivet's. -
Yeah they wanted an additional $5 either included in the envelope or charged on a cc. They call it a handling fee. I could have risked it and not put the 5 but its not worth the hassle.
I actually attached them with a little of epoxy and so far so good. I think the initial issue is that the scales are a bit bent by where the toothpick and tweezers slide in.
Sent from my iPhone using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


