Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Half Surge

Scheduled Pinned Locked Moved The Mod Squad
7 Posts 1 Posters 1.6k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Half Surge
Half Surge
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • zapikank86 Offline
    zapikank86
    Posts: 16
    zapikank86 Offline
    zapikank86
    wrote on last edited by zapikank86
    Quote Reply

      Just finished this up. I just wanted the basics. Good scissors, a knife, screw driver, and bottle opener. I might replace the bottle opener with a Super Tool saw. But I also have some questions. Later I plan to remove the inside piece that the pliers base manipulates.

      Question 1:

      When I first tried to put it back together, at first I couldn't get the main tools flush with the body. So I swapped screws and it worked fine. Are these screws supposed to be a little longer? I know the exchangable blade uses 2 washers instead of 1, but I dont think that warrants enough thickness to have a longer screw. The screws themselves are the same length it seems, but it doesnt go in as much as the other set. Is this because of some dried grease inside or something? Are these parts exactly the same or are they different? These are both screwed in as far as they will go.

      Next question. The blade exchanger, where exactly does the other washer go? I know there is one between the body and the tool. But does the extra one go below the screw or under the blade spring. I do see the washer circular mark, but I have no idea why a washer would go there and not in the same spot for the other tools.

      This:

      or this??

      1 Reply Last reply
      • zoidberg Offline
        zoidberg
        Posts: 38,161
        zoidberg Offline
        zoidberg
        wrote on last edited by
        #1 Quote Reply

          Heat the post with a lighter for a few seconds then scrape out the old loctite, repeat a few times if needed.

          This is correct.

          1 Reply Last reply
          • Kazaril Offline
            Kazaril
            Posts: 27
            Kazaril Offline
            Kazaril
            wrote on last edited by Kazaril
            #2 Quote Reply

              http://kazaril.snimka.bg/other/sur1.959984
              HTH
              the next thing to be super okay i must add some material on CO2 on back on serated blade and holder for file to ensure they stay one line and not going more :)
              whait for pictures -2-3 days and i will be finish tha 1/2 surge :P

              1 Reply Last reply
              • Poncho65 Offline
                Poncho65
                Global Moderators
                Posts: 88,523
                Poncho65 Offline
                Poncho65
                Global Moderators
                wrote on last edited by
                #3 Quote Reply

                  Great mod :like: :like: I am loving all these LM knife tools :tu: Gonna have to find a cheap Wave or Surge and try this out for myself :drool: :like:

                  1 Reply Last reply
                  • zapikank86 Offline
                    zapikank86
                    Posts: 16
                    zapikank86 Offline
                    zapikank86
                    wrote on last edited by
                    #4 Quote Reply

                      @Kazaril said:
                      http://kazaril.snimka.bg/other/sur1.959984
                      HTH
                      the next thing to be super okay i must add some material on CO2 on back on serated blade and holder for file to ensure they stay one line and not going more :)
                      whait for pictures -2-3 days and i will be finish tha 1/2 surge :P

                      I think you should swap the scissors and the plain blade. I see the little circular mark facing outward on the plain blade, it should be inward. The same with the scissors, the nail nick should be facing outwards. I dont know if it matters, but I noticed the locking surfaces are angled.

                      1 Reply Last reply
                      • Kazaril Offline
                        Kazaril
                        Posts: 27
                        Kazaril Offline
                        Kazaril
                        wrote on last edited by
                        #5 Quote Reply

                          see pictures to the end my friend, on first pictures there is concept only, and no mather who where, if you see the last pictures you see that blade and scissors are in the right places :)

                          1 Reply Last reply
                          • Obi1shinobee Offline
                            Obi1shinobee
                            Posts: 6,661
                            Obi1shinobee Offline
                            Obi1shinobee
                            wrote on last edited by
                            #6 Quote Reply

                              :multi:

                              Leatherman Half-Ass.jpg

                              1 Reply Last reply

                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                              With your input, this post could be even better 💗

                              Register Login

                              1. Home
                              2. Tool Talk
                              3. The Mod Squad
                              4. Half Surge
                              Reply
                              • Reply as topic
                              Log in to reply
                              COMMUNITY LINKS
                              EDC-TV SAKWiki GearFeed SAKSelector
                              Operational Funds

                              Help us keep the Unworkable working!

                              Make A Donation
                              November Goal: $300.00
                              Due Date: Nov 30
                              Total Receipts: $0.00
                              Below Goal: $300.00
                              0% funded
                              • Login

                              • Don't have an account? Register

                              • Login or register to search.
                              • First post
                                Last post
                              0