Non Multitools
-
@gerleatherberman said:
Hey Grant,
Why don't y'all make a category on the mto.org forum for regular hand tools? I know I'd enjoy it!
Cool stuff and nice pics!How about one for workshop tools and one for garden tools?
Got me a good grubber today. :D

-
I forgot about these two hammers, the rarest oddities I have in that category.
A glass breaking hammer and a small one the purpose of which is still unknown to me...got it in a flea market for $2
-
Hard to tell from the picture, but it looks like an old furniture hammer. Especially if there is a dimple on the square end.
-
Scutch hammer / geology hammer?
-
It's a little tile hammer.

-
I just got a set of these:

8) -
@hiraethus said:
I just got a set of these:

8)Can't go wrong with Wera

-
@50ft-trad said:
Scutch hammer / geology hammer?It's a little tile hammer.
Thanks! I ain't got no tiles to crush but I guess I'll be prepared when the time comes!

As for the geologist's hammer, I forgot about that one! It's been two or three years put away, unused, and I didn't even count it among my hammer collection! I studied Geology at University (only one year, though
). You just reminded me of it 50ft-trad :ahhhI'll try and find it and get a pic for ya folks!

-
Absolutely. I've got some Wera hex keys and torx screwdrivers too. I'll need a new pozi/flat screwdriver set soon, and I'll probably buy Wera again. The only thing I don't like about the hex key set is that the plastic sleeves can come loose. Easily fixed with a bit of superglue, but annoying.
-
Can't go wrong with Wera

Absolutely. I've got some Wera hex keys and torx screwdrivers too. I'll need a new pozi/flat screwdriver set soon, and I'll probably buy Wera again. The only thing I don't like about the hex key set is that the plastic sleeves can come loose. Easily fixed with a bit of superglue, but annoying.
I forgot that I've also got a set of Bondhus T handle hex drivers and they seem pretty well made as well
-
Can't go wrong with Wera

Absolutely. I've got some Wera hex keys and torx screwdrivers too. I'll need a new pozi/flat screwdriver set soon, and I'll probably buy Wera again. The only thing I don't like about the hex key set is that the plastic sleeves can come loose. Easily fixed with a bit of superglue, but annoying.
I like Wera - i think they're very good quality, but i prefer PB Swiss Tools. If you're after some screwdrivers, you should have a look at some of their screwdriver sets.
-
@Smashie said:
I forgot that I've also got a set of Bondhus T handle hex drivers and they seem pretty well made as wellI had a set of Bondus hex keys (the ones with the ball'd ends if you know what i mean - i cant remember what you call that?), they were pretty decent and not too expensive if i remember right... bloody heavy though.
-
@Fuzzbucket said:
I like Wera - i think they're very good quality, but i prefer PB Swiss Tools. If you're after some screwdrivers, you should have a look at some of their screwdriver sets.I've got a few Swiss Tools screwdrivers, and I do prefer their handle. The actual business end of Wera is hard to argue with though, so I ended up with mostly Wera.
-
@Vidar said:
I've got a few Swiss Tools screwdrivers, and I do prefer their handle. The actual business end of Wera is hard to argue with though, so I ended up with mostly Wera.Can't go wrong with either really - proper professional tools!
I quite fancy getting a Wera Rapidaptor - does anybody have any experience with them - any good?
PS. Did you know (Michael Caine voice)... that every individual PB Swiss Tool has it's own serial number?
-
@Fuzzbucket said:
I quite fancy getting a Wera Rapidaptor - does anybody have any experience with them - any good?I got one. Easy to use - the bit gets stuck just by putting it in. And the bit stays stuck, and loosens easily enough when it is time to change. The removal sets up the next bit for easy insertion and so on.
The one negative thing is in common with all the springy bit holder versions - they are bigger and more clumpy than the simpler plain magnetic ones. A trade off between secure bit holding vs access to tight spaces. (That trade off can be fixed by having a magnetic one too for those fairly rare tight space occasions).
-
I quite fancy getting a Wera Rapidaptor - does anybody have any experience with them - any good?
I got one. Easy to use - the bit gets stuck just by putting it in. And the bit stays stuck, and loosens easily enough when it is time to change. The removal sets up the next bit for easy insertion and so on.
The one negative thing is in common with all the springy bit holder versions - they are bigger and more clumpy than the simpler plain magnetic ones. A trade off between secure bit holding vs access to tight spaces. (That trade off can be fixed by having a magnetic one too for those fairly rare tight space occasions).
Thanks Vidar, i want to get the one with the ring magnet for working at height, so i can just stick a screw in with one hand without worrying about screw dropping off.
-
I quite fancy getting a Wera Rapidaptor - does anybody have any experience with them - any good?
I got one. Easy to use - the bit gets stuck just by putting it in. And the bit stays stuck, and loosens easily enough when it is time to change. The removal sets up the next bit for easy insertion and so on.
The one negative thing is in common with all the springy bit holder versions - they are bigger and more clumpy than the simpler plain magnetic ones. A trade off between secure bit holding vs access to tight spaces. (That trade off can be fixed by having a magnetic one too for those fairly rare tight space occasions).
Thanks Vidar, i want to get the one with the ring magnet for working at height, so i can just stick a screw in with one hand without worrying about screw dropping off.
Just bought one - the price had dropped to just a fiver plus postage!

-
Lots of great tools guys
I have yet to take any pics of any of my regular tools
I will try to before long though 
-
Did somebody say hammers? :D

This is my Stanley FUBAR Fat Max, and I've had it for a number of years now. As you can see, it has been used quite a bit.

This particular model is the 55-119 version, which I now see is also available in yellow. I think I may have to get another one eventually....

Mine says Patent Pending on it, so I guess I shouldn't have used it- I should have kept it pretty and scratch free for future FUBAR collectors. :facepalm:

They must mean it too, because this warning is also molded into the handle. That having been said, I don't think I have ever worn safety glasses when using it and I still appear to be alive.

As I said, this one has a fair bit of mileage on it. It is often my primary hammer when repairing decking or doing any serious construction or demo work, and I have never felt like it was lacking. I will admit though that the jaws on the back don't get that much use. They are meant for grabbing boards and stuff, but I really don't use it for that too often, even when working with boards.

I do however use the pry bar and nail puller end almost as much as I use the hammer.
I like it and I would encourage anyone who needs a solid tool that they can abuse with impunity to give one of these a shot if you haven't already. If that doesn't convince you, then this ad, which made me buy one in the first place probably will! :D
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
Def
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
