What Regular Tools Do You Use?
-
I'd like to see what regular tools everyone uses. They determine what kind of Multitools I like to carry.
Post pics if you can take them easily.
I have an assortment of Crafstman & other tools. Here are my favorites that go in my toolbox I carry around the house on "fix-it" days.
Facom locking pliers
Sears aviation snips
Sears slip-joint pliers (French made)
Sears stubby screwdrivers -
Sears Clench Wrenches (at lonediver's suggestion)
Sears nippers & needle nose
Sears adjustable wrenches
Prybar & pencil -
File & hacksaw
Stanley utility knife & Shoe Goo (for strong general glue)
Assorted small pliers, picks, & files
Small Vise Grips -
I used to collect and sell tools. In the photos, I will show tools I actually use more often which may be of interest to forum readers.
Here are some combination screwdrivers. Though I prefer dedicated, single size screwdrivers, I end up using these combination screwdrivers often so I won't have to make return trips to the tool chest for the right size driver. The Enderes and Xcelite 600 can be used as nutdrivers, though they have only 2 size hex sockets.
The Xcelite M-60 is a set of tiny screwdrivers. They are great for working on miniature electronics and eyeglasses, but cannot survive much torque.
I have been using these Xcelite tools for over 25 years and the Enderes for probably about 15 years.


-
I use these screw-holding screwdrivers when I need to insert a screw in a location where there is not enough clearance to hold the screw with a hand.
The flat bladed models are made by Quick-Wedge(Salt Lake City, Utah) and the Phillips driver is a Sears Craftsman.

-
I use these Easydriver ratcheting screwdrivers for woodworking when I need high torque with good control.
They place less stress on the wrist than a conventional screwdriver because you can grip the spherical handle from a variety of positions. The Easydrivers were made by Creative Products, Inc. in Bennington, Vermont.

-
Here are a few misc. tools I use regularly. They include a 2 full sets of hollow shaft nutdrivers, one made by Xcelite and the other by Vaco (only one of each nutdriver shown). The reamer enlarges holes and the thread chaser and pick are self explanatory.
The Swiss-made General 6 inch dial calipers permit fairly accurate measurements and have earned their keep many times over. I inherited several Starrett and Brown and Sharpe professional micrometers, but haven't used them much because I haven't required the precision.

-
I still have one of those Easydrivers somewhere in the garage. I'll have to dig it up.
-
I carry this set of Elkind metric hex key wrenches in the toolbag of my recumbent bicycle. Where longer reach is required, I use a set of metric or inch Xcelite 99-series hex drivers.
I also have a set of Xcelite wrenches which fit Bristol Spline screws, rare fasteners which were used to hold knobs on old military radio equipment.

-
There are many files around here, from tiny to large, but these are the files most often used. Note the homebrew handles made from a golf ball and a soft rubber wire end cap.
The Clauss 925 scissors, a souvenir of the telephone industry, is as tough as you'll find.

-
These cushion grip VACO crimpers are for fastening insulated and uninsulated terminals on the end of wires.
I became a fan of using crimp terminals on larger gauge wires after working on a power supply assembly line one summer. For double protection, I solder the uninsulated terminals after crimping.

-
Read the first post in the thread. I figured that showing our regular tools would help understand what we want in a multitool.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login