Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Hacker Badge Request

Scheduled Pinned Locked Moved The Mod Squad
6 Posts 1 Posters 1.0k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Hacker Badge Request
Hacker Badge Request
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Higgins617 Offline
    Higgins617
    Posts: 3,350
    Higgins617 Offline
    Higgins617
    wrote on last edited by
    Quote Reply

      More a repair than it is a true mod, but I thought it counted as it did involve disassembly and alteration of the original design. Backspring on my Schrade Tough Tool had sprung, rendering the whole side of tools(phillips, file, and blade included) useless. And these were all tools I used frequently when I carried it, so it's sat for over a year and I finally got the idea to say screw it and try to fix it. So here goes.

      Materials Needed: Dremel or similar rotary tool, Carbide cut-off wheel for rotary tool, Hammer, Punch, Solvent, 3.5MM Allen screw and bolt, Ziptie

      Here is a shot showing the issue, which seems to be fairly common for these tools unfortunately.

      First step was to take the dremel and grind/cut one side of the rivet off to allow it to be punched out. Once punched out, the tools can be removed in one clump to maintain order of tools and washers. This is where the ziptie comes it, I slid it through the tools to keep them in the correct order.

      The solvent was used to try to clean up the inside of the tool a bit, not required, but mine was pretty grungey. Then the hammer and punch came back out to "persuade" the backspring to be a spring once more. Sitting just below parallel with the handle edges resulted in a more solid snap than it had prior to breaking. Next, and final step was reassembly, which was fairly painless. Slotted the tools onto the bolt one by one, pushing the bolt a little further in each time. Once in, the nut was torqued on until I felt the tools had adequate friction between them. I went pretty snug as I liked the additional confidence in lockup the tightness adds. Once torqued, I dremeled off the excess bolt and gave the end a few raps from the hammer to deform it enough to discourage backing out.


      Not exactly a precision engineered fix, but it got a favorite tool of mine back in action, and I'm pretty happy with the feel and lockup of it.

      Be glad to hear any thoughts.

      1 Reply Last reply
      • Sam Lim Offline
        Sam Lim
        Posts: 2,306
        Sam Lim Offline
        Sam Lim
        wrote on last edited by
        #1 Quote Reply

          :like:

          I only dream is that all MT are using screws and nut! It's a real pain working with rivets!

          1 Reply Last reply
          • hiraethus Offline
            hiraethus
            Admin Team
            Posts: 6,969
            hiraethus Offline
            hiraethus
            Admin Team
            wrote on last edited by
            #2 Quote Reply

              Good hack. :like: You should submit a proper badge request though - it's tricky to assign a badge to you if you if you don't. I've done it for you this time though. :tu:

              1 Reply Last reply
              • Higgins617 Offline
                Higgins617
                Posts: 3,350
                Higgins617 Offline
                Higgins617
                wrote on last edited by
                #3 Quote Reply

                  @hiraethus said:
                  Good hack. :like: You should submit a proper badge request though - it's tricky to assign a badge to you if you if you don't. I've done it for you this time though. :tu:

                  Sorry boss, don't quite know what I'm doing and didn't read directions correctly :oops:

                  Thank you

                  1 Reply Last reply
                  • Poncho65 Offline
                    Poncho65
                    Global Moderators
                    Posts: 88,523
                    Poncho65 Offline
                    Poncho65
                    Global Moderators
                    wrote on last edited by
                    #4 Quote Reply

                      Great mod/fix and congrats on the badge :tu: :like:

                      1 Reply Last reply
                      • MusicMen Offline
                        MusicMen
                        Posts: 2,320
                        MusicMen Offline
                        MusicMen
                        wrote on last edited by
                        #5 Quote Reply

                          Congratulations on the badge :cheers:
                          Nice mod :tu:

                          1 Reply Last reply

                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                          With your input, this post could be even better 💗

                          Register Login

                          1. Home
                          2. Tool Talk
                          3. The Mod Squad
                          4. Hacker Badge Request
                          Reply
                          • Reply as topic
                          Log in to reply
                          COMMUNITY LINKS
                          EDC-TV SAKWiki GearFeed SAKSelector
                          Operational Funds

                          Help us keep the Unworkable working!

                          Make A Donation
                          November Goal: $300.00
                          Due Date: Nov 30
                          Total Receipts: $0.00
                          Below Goal: $300.00
                          0% funded
                          • Login

                          • Don't have an account? Register

                          • Login or register to search.
                          • First post
                            Last post
                          0