Maintenance Day!
-
I usually just oil then and keep them sharp
but I have used several methods for cleaning them up after buying them second hand 
I have used a vinegar bath for rust, a rust eraser and even sand paper to clean tools
I usually use either a mineral oil or a dry type lube like 3in1 oil that dries quickly
I have also use polishing paste to shine metal as well 
-
Nice looking set of knives, Barry!
I usually sharpen and strop as I go. If I use a knife, I'll strop it....if I have the chance. I like to keep my knives ready for use at awl times.
For lubricants, I like mineral oil or Ballistol. The drawback of Ballistol is that it can dry and become gummy, so thin coatings are recommended. The upside of Ballistol is that it cleans as well as lubricates--it is sort of the original CLP. It is also non-toxic, so you can use it to clean your knives (and firearms) and not worry about then using them on food or game. Same for food-grade mineral oil.
If I get some real gunk on my knives, I'll clean them with alcohol, kerosene, or WD-40. But, after the gunk is cleaned off, I clean them with soap and water, and then Ballistol.

-
Sidol metal polish for anything metal -like or scratched up.
Warm soap bath with a toothbrush rub down and some mineral oil to top it off.
My besties get genuine Vic oil...Sharpening happens in between and I usualy get amazing results on my honing steel.
-
That Balistol looks great...
US product?
Never seen it here. -
@Mechanickal said:
That Balistol looks great...
US product?
Never seen it here.Mechy, the original formula is from.....Germany. I think that's a country in Europe. So it may be hard for you to find. Let me know and I'll see if I can smuggle some to you.

-
That Balistol looks great...
US product?
Never seen it here.Mechy, the original formula is from.....Germany. I think that's a country in Europe. So it may be hard for you to find. Let me know and I'll see if I can smuggle some to you.

Seems like it's for sale on the same site that sells insurge... I mean Paramilitaries here

-
From the MSDS (Material Safety Data Sheet):
Most corrosion inhibiting lubricants can only protect against normal oxidation. They do so by covering up the surface,
which they are supposed to protect, and prevent contact with water and air. Due to its alkalinity Ballistol can also protect
against galvanic corrosion, acidic corrosion and salt water corrosion. Ballistol contains oxygen binders. They make the
oxygen, contained in water or air, unavailable for oxidation. Due to its low surface tension, Ballistol is capable of
creeping into the smallest openings even against gravity. Accordingly, Ballistol provides not only passive but also active
protection against corrosion. However, Ballistol is not a permanent coating or paint. Its protective effect will be the stronger the more often it is re-applied. -
Usually just a quick couple swipes on the Lansky Turnbox and a little mineral oil for lube.
-
Wipe everything to get rid of gunk, use picks in tight places, WD-40 for tougher stuff, and sharpen on ceramic rods or a Lansky set.

-
Thanks guys! My yellow scales are my users but I still like to keep them looking good! I have check out that Ballston Nix. There's plenty of uses for it around out house!
-
The tools I use often I typically clean up and touch up weekly or more if needed. My routine is to inspect then proceed as follows. To clean I'll use soap and water with an old toothbrush. If I need to really get into the cracks and crevices then I'll opt for a toothpick and paper-towel following a soak in hot soapy water. For the blades, I'll strop if only touch up is needed. Typically my SAK falls into this category. My Charge TTi rarely needs anything but I like to strop because, well, I like the process. If my SAK has been used a lot then I'll give it a few swipes on my Spyderco ceramic rods then strop.
I don't remove scratches anymore on my tools. I only remove damage that hinders the use of the tool. Every now and again I might give my SAK scales a once over on green compound I use for stropping. That shines up the scales nicely without actually removing scratches.
-
Awesome thread!

-
I just clean and oil the users for the most part, and just use mineral oil since it's food safe. If I'm storing carbon steel for a while though, I coat the blades with Tuf-Cloth dry lubricant. It's a great product for this, as it leaves a thin dry wax-like coating on the steel that will not let moisture through. It works great on blued steel as well, and love the smell of it.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
