Cryogenic metals ???
-
In the lofty world of benchrest target shooting cryogenicly treated barrels have been the goto for several years. They claim it relives stresses in the metal.
Now Buck has started treating blades for the new 110 & 112 slim cryogenicaly. They are claiming it makes the blade hold an edge longer??????????????????
Comments anyone? -
It's basically just cool sounding. High alloy stainless steels (Elmax, RWL-34, that kind of stuff) needs very low temperatures to remove the last austenite, but -85 °C is sufficient. Using liquid nitrogen and going down to -190 °C is perfectly fine, but does not bring any extra advantages either.
-
I can understand the stress relief in barrels, but I don't see why it would make a blade hold an edge longer. I suspect sales gimmick ............ :ahhh :ahhh

-
I'm not a metallurgist, but with my limited knowledge, I know of no technical reason for doing cryogenic cooling of blade steels, so... Yeah, I'm leaning towards marketing BS as well.
-
@Butch said:
In the lofty world of benchrest target shooting cryogenicly treated barrels have been the goto for several years. They claim it relives stresses in the metal.
Now Buck has started treating blades for the new 110 & 112 slim cryogenicaly. They are claiming it makes the blade hold an edge longer??????????????????
Comments anyone?Cryogenic treatment was used in the military in WW2 so it's not new or advertising hype. If a company just wanted hype they could call their steel surgical unobtainium.
Short quote from Buck. "Heat treating is the process used to impart special qualities to metals and alloys (hardness, strength, ductility, etc.). When heat and subsequent cooling are applied to metals in their solid state, the physical and structural properties <u>(but not the chemical composition)</u> of these metals are changed."My experience with 420HC is a blade might go from cutting 40 plus feet of cardboard to 60 feet of cardboard before reaching the same level no dullness.
There are steels that can cut 10 times that much cardboard so a 15% increase over that would be a lot of cutting.Here's an article on it. https://blademag.com/blog/frozen-sharp-cryogenically-treated-blades
-
The buck statement describes the annealing of steel, performed by all. https://en.m.wikipedia.org/wiki/Annealing_(metallurgy)
There is a balance to be struck between making the edge/blade hard and making it too brittle
-
T Y for the links.Have to leave right now but will read them as soon as I get the chance.
-
I've read and watch some really informative info on why certain steels can benefit from cryogenic treatment. While I am nowhere near as knowledgeable as most in metalurgy Jay Fisher certainly is.
https://jayfisher.com/Heat_Treating_Cryogenic_Processing_of_Knife_Blade_Steels.htm -
Well, if that treatment doesn't increase the quality of the metal, at least you still get a cool blade...

-
@pfrsantos said:
Well, if that treatment doesn't increase the quality of the metal, at least you still get a cool blade...
Waa waarr. :D
-
I was aware of the annealing process, but could not understand any benefit coming from just freezing the holy hindend off of a blade. Apparently there is great benfit from if. See even an old codger like me can learn something new. Thanks for the info fellas. ...........

-
from a metallurgist who speSmurfpillses in knife steels (Larrin, owner and creator of knifesteelnerds):
"The primary effect of cryogenic processing is to reduce retained austenite which gives you an increase in strength and hardness. That usually also reduces toughness though not always: https://knifesteelnerds.com/2018/06/04/ ... ar-z-wear/
There is also scientific literature suggesting there is an increase in wear resistance due to increased carbide precipitation (I can't go into that in any detail without a whole article on it). In the 154CM CATRA article there was no benefit from cryo outside of hardness: https://knifesteelnerds.com/2018/06/18/ ... retention/
That doesn't necessarily mean that there is never a benefit for edge retention with cryo but contradicts some of the wild reports like 500% increase in wear resistance with cryo."
-
@ThePeacent said:
from a metallurgist who speSmurfpillses in knife steels (Larrin, owner and creator of knifesteelnerds):"The primary effect of cryogenic processing is to reduce retained austenite which gives you an increase in strength and hardness. That usually also reduces toughness though not always: https://knifesteelnerds.com/2018/06/04/ ... ar-z-wear/
There is also scientific literature suggesting there is an increase in wear resistance due to increased carbide precipitation (I can't go into that in any detail without a whole article on it). In the 154CM CATRA article there was no benefit from cryo outside of hardness: https://knifesteelnerds.com/2018/06/18/ ... retention/
That doesn't necessarily mean that there is never a benefit for edge retention with cryo but** contradicts some of the wild reports like 500% increase in wear resistance with cryo."**
I thought that you could always dismiss claims like that. :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login