Farmer X mod.
-
So, I've gathered all I need.
2 donors, pin stock and some guts.
I'll probably build it without torx screws.
The sourcing of M2 screws seem to be a hassle here and my dad is currently lacking the time to drill and thread the pins.3mm rods ✓, 2.5mm rods ✓
How much will they need to protrude before peening?
About 1mm like with 91mm models?I hope to start today or later this oncoming week.
-

If it was me, I would try slightly more than 1mm first. You can always grind some off! -
This will be interesting

I'd say 1mm is enough, though I couldn't argue with Pabs either.
I guess it depends on how you would like to have the pins end shaped then. Kinda half-round? Or flat (like the famous Masterwaiter)?
-
I am wondering about the same question too.

Really am no expert here, but I just tested with 1mm and 0.7mm on each side of the alox yesterday and today. The 0.7mm per side felt like there's insufficient material to full up the rivet/countersink hole, and 1mm looks ok, but kinda flat. As a reference, I did the 91mm peening practice today as well, and found that 0.5mm(per side) actually works quite well, it should fill up the countersink and almost flush against the bushing once it is done.
-
Donors:

Disassembly


Fitting:



After alot of taps:



My backside peens are a bit larger than the front ones. But at least they're consistent on each side.
I will probably polish them off somewhere during the week. For now, I'm just glad I was able to finish it on a single afternoon.
Any thoughts on my peening so far are greatly appreciated. Bear in mind this was my first full mod :D
-
@Mechanickal said:
Donors:

Disassembly


Fitting:



After alot of taps:



My backside peens are a bit larger than the front ones. But at least they're consistent on each side.
I will probably polish them off somewhere during the week. For now, I'm just glad I was able to finish it on a single afternoon.
Any thoughts on my peening so far are greatly appreciated. Bear in mind this was my first full mod :D
Mechanical, that was really nicely done! You are a natural!

So for your mod, how much did you leave on each side? 1mm?

-
I peened the first halves while the rods were in a vise. I test fitted them in the front scale every now and then. I left about about a mm for the backside but went more by feeling than measurements :D
-
Really really nice!
-
@Mechanickal said:
I peened the first halves while the rods were in a vise. I test fitted them in the front scale every now and then. I left about about a mm for the backside but went more by feeling than measurements :DThank you, it really does look well done.
Please do keep us posted on longer term use, some would say pre-peening may loosen up over time, and I am just on the fence whether to try this or not. -

Thank you for the kind words
-
Well done! I love it!

-
That's nicely done Nick

Sure it doesn't look like factory, but it looks solid and consistent.
Aaaaand you didn't hammer into the scales!
-
Insulation tape for the win!
-
Oh, I can also mention that all tools snap open and closed, and there is zero sideways play in any of the tools.
-
Great job! My first attempt at peening didn’t turn out nearly as good as yours.
-
@Mechanickal said:
Insulation tape for the win!
-
Looks good Nick!
-
Top job there Nick!

-
Nice work!
[It's not failure if you learn something from it]
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login