Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Mod failure.

Scheduled Pinned Locked Moved The Mod Squad
49 Posts 1 Posters 4.4k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Mod failure.
Mod failure.
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Nix Offline
    Nix
    Posts: 24,263
    Nix Offline
    Nix
    wrote on last edited by
    Quote Reply

      I just too frustrated at the moment to even start........

      I tried to take an old Explorer apart in order to use it build my idea of a TSA-friendly "Toothless Old Explorer", but it was a complete disaster. :td:

      Taking the scales off was pretty straightforward. Not my first removal.

      I was just planning on removing a layer, so I though I could salvage the pins and bushings to re-use when turning a 4-layer into a 3-layer.

      I tried drilling out the pins while preserving the bushings, but this didn't go so well with freehand drilling. So I tried using a grinding stone to remove enough of the upset pin to be able to drift the pins out. That worked OK for the smaller pin (back side bushing trashed). But I found I couldn't get the larger pins free of the bushings. I ended up grinding pins and bushings away until I could drift the remaining pins out. In the process of doing so one of the aluminum spacers got bent a bit.

      The spring pin was even harder to remove!

      I ground that down and drifted it out of one layer, but the it got stuck (bent?). After trying to work that out for a bit, the back side spacer got bent. :oops:

      Eventually it all came apart (there is nothing I can't destroy.) but the process was so chaotic that I have no idea what spring goes with what tool. I only have half the bushings. A couple of spacers are bent. And I think the small pin (easiest to remove) has a slight bend. :dwts:

      Just for fun, I though I'd try to stack the bits back together, but I couldn't even get the first large pin back into the established hole. (Nice tolerances, Vic.)

      So I just trashed an nice, slightly grimy, used Explorer for no good reason. >:(

      Feels like my modding career is over before it even begins....... :facepalm:

      1 Reply Last reply
      • Wspeed Offline
        Wspeed
        Posts: 76,225
        Wspeed Offline
        Wspeed
        wrote on last edited by
        #1 Quote Reply

          That’s a shame Nix :facepalm:
          But practice makes perfect :tu:
          I can’t talk as I have never tried taking
          a SAK to bits yet or tried to mod one :dunno:

          1 Reply Last reply
          • Don Pablo Offline
            Don Pablo
            Posts: 15,329
            Don Pablo Offline
            Don Pablo
            wrote on last edited by Don Pablo
            #2 Quote Reply

              ASSUMING that the pins are not bent, try sanding a small taper on the ends of the pins that you cut.
              That's to ttally make sure that there isn't a small amount of material remaining from the cutting/grinding process that is sticking out, making the pin a bit bigger in diameter.
              That way it could slide back into the hole more easily.


              .
              _______/

              1 Reply Last reply
              • RF52 Offline
                RF52
                Posts: 5,787
                RF52 Offline
                RF52
                wrote on last edited by
                #3 Quote Reply

                  Check the exploded SAK thread if you need to double check what goes where [emoji106]

                  favicon

                  (r.tapatalk.com)

                  Sent fra min FRD-L09 via Tapatalk

                  1 Reply Last reply
                  • Nix Offline
                    Nix
                    Posts: 24,263
                    Nix Offline
                    Nix
                    wrote on last edited by
                    #4 Quote Reply

                      Good reference, RF. :tu:

                      Pabs, I did lightly sand the one pin before trying to re-insert it. Didn't actually taper it, but did--as you suggest--want to be sure the wasn't any extra material at the end.

                      I think I need to find a better way to remove the pins. A drill press seems like a good step, but even that isn't a clear answer. How do you guys remove the pins? Do you save the bushings?

                      (And where do I get new bushings? :think:)

                      1 Reply Last reply
                      • kottskrapa Offline
                        kottskrapa
                        Posts: 4,186
                        kottskrapa Offline
                        kottskrapa
                        wrote on last edited by
                        #5 Quote Reply

                          I usually drill them out and use a nail driver that I have sanded down to drive the pins out. That saves the bushing.

                          I can send you new pins if you want but I don't think I have any bushings left

                          [It's not failure if you learn something from it]

                          1 Reply Last reply
                          • Don Pablo Offline
                            Don Pablo
                            Posts: 15,329
                            Don Pablo Offline
                            Don Pablo
                            wrote on last edited by
                            #6 Quote Reply

                              @Nix said:
                              I think I need to find a better way to remove the pins. A drill press seems like a good step, but even that isn't a clear answer. How do you guys remove the pins? Do you save the bushings?

                              I use free-hand drilling with a Dremel.
                              It wouldn't be possible without using a pointy punch to punch a divot into the pin, dead centre, so the drill doesn't wander and wreck the brushing. :dwts:
                              Then as soon as the brushing starts spinning with the drill, I stop, and start punching out pins with another punch.

                              I still haven't gotten through a small bag of brushings that I bought from Syph, and some more from other members here. Mostly because I've bought super cheap trashed SAKs just to scrap for brushings. :D

                              1 Reply Last reply
                              • Mike 56 Offline
                                Mike 56
                                Posts: 1,705
                                Mike 56 Offline
                                Mike 56
                                wrote on last edited by
                                #7 Quote Reply

                                  I start with a small drill bit about the size of the brass pin then I finish with a larger drill bit that is larger than the bushing. when you have drilled deep enough the bushing will just come off. I have a 1/16 pin punch to drift the pins out. One time I put a SAK together without bushings and glued the scales on using goop glue it drys rubbery and won't harm the scales like super glue.

                                  1 Reply Last reply
                                  • Nix Offline
                                    Nix
                                    Posts: 24,263
                                    Nix Offline
                                    Nix
                                    wrote on last edited by
                                    #8 Quote Reply

                                      :like:

                                      1 Reply Last reply
                                      • Nix Offline
                                        Nix
                                        Posts: 24,263
                                        Nix Offline
                                        Nix
                                        wrote on last edited by
                                        #9 Quote Reply

                                          I'm going to try to salvage some bushings off another old SAK. Not sure about the pins, might be able to use what I have. :dunno:

                                          1 Reply Last reply
                                          • Huntsman Offline
                                            Huntsman
                                            Global Moderators
                                            Posts: 5,781
                                            Huntsman Offline
                                            Huntsman
                                            Global Moderators
                                            wrote on last edited by
                                            #10 Quote Reply

                                              Yes - I remember my first modding experience (I've still only done about three) ...... Not as easy as you'd think!!

                                              All the amazing modders here make it look so easy - When you do it yourself - Not so!!

                                              Keep at it - Some good tips in here

                                              1 Reply Last reply
                                              • Mike 56 Offline
                                                Mike 56
                                                Posts: 1,705
                                                Mike 56 Offline
                                                Mike 56
                                                wrote on last edited by
                                                #11 Quote Reply

                                                  I found brass rod at a Hobby Town. The large was all most perfect the smaller was a little small bit works. Do you have one near you?

                                                  1 Reply Last reply
                                                  • jaya_man Offline
                                                    jaya_man
                                                    Global Moderators
                                                    Posts: 9,012
                                                    jaya_man Offline
                                                    jaya_man
                                                    Global Moderators
                                                    wrote on last edited by
                                                    #12 Quote Reply

                                                      Good tips everyone... Sometimes some saks will need a little bit of persuasion... especially those old and dirty ones...

                                                      Here’s how I mutilate mine...

                                                      1. Center punch the pins
                                                      2. Using a Dremel like rotary tool, drill the pins until the bushings spin free or if not, approximately deep enough that it doesn’t go through the outer liner... very crucial if you only need to reduce a single layer
                                                      3. I use 2.5mm drill bit on all but the middle pin with bushing... 2mm drill bit for the middle pin with bushing
                                                      4. Additionally, I drill the center pin without bushing a little further (but not going through the outer liner) with a 2mm drill bit just to make it easier to punch through. 2.2mm drill bits are hard to find in my area...
                                                      5. Use a nail punch (close to similar diameter as the pins) tonpush the pins through the bushings and layer per layer... sometimes the pins are softer than usual... using a smaller diameter punch will just simply ruin the pins.
                                                      6. Arrange the removed layers from top to bottom... easily done if removing layer per layer...
                                                      7. Take pics with mobile phone... handy when its time for assembly...
                                                      8. For 93mm saks, I follow Syph’s tip. Drill and push out the center pin first...

                                                      Sent from my iPhone using Tapatalk

                                                      1 Reply Last reply
                                                      • Nix Offline
                                                        Nix
                                                        Posts: 24,263
                                                        Nix Offline
                                                        Nix
                                                        wrote on last edited by
                                                        #13 Quote Reply

                                                          Good tips, J-man. :tu:

                                                          When you say "drill and center punch the center pin first, which center pin? (the center pin with the bushing? Or the center pin (what I called the 'spring pin') without the bushing?) :think:

                                                          1 Reply Last reply
                                                          • Nix Offline
                                                            Nix
                                                            Posts: 24,263
                                                            Nix Offline
                                                            Nix
                                                            wrote on last edited by
                                                            #14 Quote Reply

                                                              @Mike 56 said:
                                                              I found brass rod at a Hobby Town. The large was all most perfect the smaller was a little small bit works. Do you have one near you?

                                                              I do! :tu:

                                                              And we have a good hardware store that may carry some brass rod material. I can always make a rod thinner...... :D

                                                              1 Reply Last reply
                                                              • Nix Offline
                                                                Nix
                                                                Posts: 24,263
                                                                Nix Offline
                                                                Nix
                                                                wrote on last edited by
                                                                #15 Quote Reply

                                                                  @jaya_man said:
                                                                  7. Take pics with mobile phone... handy when its time for assembly...

                                                                  Yeah, that was my plan. I even had my cell phone in my pocket. And then it awl sort of exploded.......

                                                                  I should have used some wire to replace the pins as I took them out, thereby keeping the set up intact and awl the pieces in one room....and inside the house.....in the same county...... :facepalm:

                                                                  1 Reply Last reply
                                                                  • Sos24 Offline
                                                                    Sos24
                                                                    Global Moderators
                                                                    Posts: 11,507
                                                                    Sos24 Offline
                                                                    Sos24
                                                                    Global Moderators
                                                                    wrote on last edited by
                                                                    #16 Quote Reply

                                                                      Sorry to hear of the setback (not failure because it doesn’t sound like your giving up yet).

                                                                      You have more courage than me. The SAKs to make my envisioned mod are still sitting in a drawer, and after this thread may be sitting there for a while. Then again I failed at trying to change a watch battery the other day when the battery screw went flying to God knows where.

                                                                      I’m confident that you’ll get it down, especially with all the great recommendations here.

                                                                      1 Reply Last reply
                                                                      • BClogic Offline
                                                                        BClogic
                                                                        Posts: 2,051
                                                                        BClogic Offline
                                                                        BClogic
                                                                        wrote on last edited by
                                                                        #17 Quote Reply

                                                                          Nix, when the going gets tough I sometimes walk away to clear my head. I popped open a 4.2 Audi S6 to find the chain guides for the variable cam timing actuator broken. Upon reassembly I couldn’t get the cams to line up perfectly without oil pressure, I started to get frustrated because I didn’t want engine damage, walked away and came back knowing that I was doing the job right. Start day she spun and purred like a kitten. I guess what I mean is keep your head in the game and walk away when necessary. It helps!

                                                                          Sent from my iPhone using Tapatalk

                                                                          1 Reply Last reply
                                                                          • Nix Offline
                                                                            Nix
                                                                            Posts: 24,263
                                                                            Nix Offline
                                                                            Nix
                                                                            wrote on last edited by
                                                                            #18 Quote Reply

                                                                              :tu:

                                                                              I've stepped back to regroup and reload. Plan A failed, but I have a Plan B to get some supplies and reengage. Plan C might be a call to Syph....... :rofl:

                                                                              1 Reply Last reply
                                                                              • BClogic Offline
                                                                                BClogic
                                                                                Posts: 2,051
                                                                                BClogic Offline
                                                                                BClogic
                                                                                wrote on last edited by
                                                                                #19 Quote Reply

                                                                                  Never hurts to ask from someone who has taken the test either!

                                                                                  PS when I walked away I called an Audi tech and he said “don’t worry, everything will be fine”

                                                                                  Sent from my iPhone using Tapatalk

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 3
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. The Mod Squad
                                                                                  4. Mod failure.
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0