Mod failure.
-
@jaya_man said:
Good tips everyone... Sometimes some saks will need a little bit of persuasion... especially those old and dirty ones...Here’s how I mutilate mine...
- Center punch the pins
- Using a Dremel like rotary tool, drill the pins until the bushings spin free or if not, approximately deep enough that it doesn’t go through the outer liner... very crucial if you only need to reduce a single layer
- I use 2.5mm drill bit on all but the middle pin with bushing... 2mm drill bit for the middle pin with bushing
- Additionally, I drill the center pin without bushing a little further (but not going through the outer liner) with a 2mm drill bit just to make it easier to punch through. 2.2mm drill bits are hard to find in my area...
- Use a nail punch (close to similar diameter as the pins) tonpush the pins through the bushings and layer per layer... sometimes the pins are softer than usual... using a smaller diameter punch will just simply ruin the pins.
- Arrange the removed layers from top to bottom... easily done if removing layer per layer...
- Take pics with mobile phone... handy when its time for assembly...
- For 93mm saks, I follow Syph’s tip. Drill and push out the center pin first...
Sent from my iPhone using Tapatalk
These are really solid advice, great job!Nix, sorry to hear about the setback, but don't let that hold you back.
Here are some my photo/experience from my first mod:
Some kind of jig is important to me, it keeps the chassis level when taped onto the jig. I drilled four holes into the wood and it doesn't even have to be 100% accurate. In fact, drilling four larger holes will allow the pin/bushing to pass thru when you are 'punching' out the pin, layer by layer.

Center punch is absolutely must for me, I have run-out problem with drill press when I am not careful. I can't imagine how I am going to mod without the center punch...the backside tool pin(the most bottom pin), I will file it flat and then center punch that.

I admit having a drill press really does make things easier, but using a dremel to take out the bushing/pin is a totally viable option. I usually use a tiny diamond dremel bit to hollow out the content inside the bushing slowly, especially when I failed to drill accurately into the bushing. Since it is not possible to know how deep I should drill and everything is just educated guess, so from time to time, I will stop and try using the cutter to try to lift the bushing up. If I feel there is wiggle room, I know I am very very close. Most of the times, the rivet will get so thin that you could just literally lift the bushing off without any damage.

For assembly, I built a second jig, this time with liner as a guide, I could mark on the wood and drill those 4 holes with much higher accuracy. This jig is great for keeping everything inline and straight, especially for the first few layers since the spring/tool tension might warp the whole thing funny. The chauffeuring on top of each pins do help.

Hope these helps a little!

-
-
Good stuff, comis!

-
Beautiful pics, Comis.

-
... sorry Jack 
This is totally normal even for the second mod.
When I decided to do my first mod I've prepared for the worst after reading a couple of SAK mod threads here :DApart from the excellent advice already given I found it very important not to rush things and rethink any next step.
And building a simple jig for re-assembly is a very good idea.PS, if you get stuck at re-assembling the scissors layer then I found a little trick to get it done (see below).
I've used a punch/pin that is thinner than the scissors layer to push back the spring before adding the scissors.
Then the scissors can be added pushed down far enough so that the spring stays in place.
You then keep pressing the scissors down while pulling out the punch/pin.Hope it makes sense

Good luck and don't give up.


-
@McStitchy said:
... sorry Jack 
This is totally normal even for the second mod.
When I decided to do my first mod I've prepared for the worst after reading a couple of SAK mod threads here :DApart from the excellent advice already given I found it very important not to rush things and rethink any next step.
And building a simple jig for re-assembly is a very good idea.PS, if you get stuck at re-assembling the scissors layer then I found a little trick to get it done (see below).
I've used a punch/pin that is thinner than the scissors layer to push back the spring before adding the scissors.
Then the scissors can be added pushed down far enough so that the spring stays in place.
You then keep pressing the scissors down while pulling out the punch/pin.Hope it makes sense

Good luck and don't give up.You should have been called McPlaster.

-
McPatchy!
-
@Mechanickal said:
McPatchy!:o

-
You're just jealous about my new name Nicky :D
-
These are some of my favorite SAK modding tools. For me it is much easier for me to use a spring loaded center punch to find the center of the pins. I prefer a lighter hammer. Their is no right way keep at it and you will get it.

Sent from my iPhone using Tapatalk
-
I've got a spring punch that will get pressed into service..... Sorry about the pun there..... *(not really) *

-
If I can do it then so can you! Worst case is more trying
[It's not failure if you learn something from it]
-
Scrounging for donors right now..... :D
-
Every time I see this thread pop up - I think it's going to say that me, or one of my MT.o colleagues, has done something wrong, and will be in trouble with the big boss.
-
That's a good way to wake up quickly. :D
-
@Nix said:
Yeah, that was my plan. I even had my cell phone in my pocket. And then it awl sort of exploded.......I should have used some wire to replace the pins as I took them out, thereby keeping the set up intact and awl the pieces in one room....and inside the house.....in the same county......


-
@Huntsman said:
Every time I see this thread pop up - I think it's going to say that me, or one of my MT.o colleagues, has done something wrong, and will be in trouble with the big boss.
@Nix said:
I've got a spring punch that will get pressed into service..... Sorry about the pun there..... *(not really) *
I actually prefer the manual punch, maybe the spring punch I got was a dud, it got too much slack in it to be reliable enough to punch at dead center.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

