Wave/Charge Awl / Precision Screwdriver
-
I know a lot of folks here would like an awl on the Wave/Charge MTs. I had a thought, but guess itcmust have been thought of already.
Has anyone tried grinding the tip of the precision screwdriver to a relatively sharp point, to function like a makeshift awl?
I thought the advantage of this would be that you could still fit a non modded screwdriver in the sheath. The bit could be modded by putting it in the collet of a Dremel or similar rotary tool and grinding it against something; or just touching it on a grinding wheel.
I know it wouldn’t be like a proper awl, but could perform some of the tasks you’d use an awl for.
Perhaps this has already been discussed on here..
Cheers
Omar

-
I have tried and i didnt like it, its way too small and it breaks easily when it bends little, i use scissors as awl if i dont have any other tool with awl.
Only Tools Matters
-
@Antti Lammi said:
I have tried and i didnt like it, its way too small and it breaks easily when it bends little, i use scissors as awl if i dont have any other tool with awl.Only Tools Matters
Thanks Antti Lammi.
I thought it might have been too optimistic!
Did you manage to find an awlternative solution other than the scissors? Couldn’t resist!

-
Actually i have found alternative way for it but you need long bits from MUT and grind it to shape of awl, and you have full size removable awl.
It has few cons vs real awl
If it gets stuck bit cant be pulled out like regular awl cause bit stays on and it leaves from bit holder.
There is reason why many mod awl on wave/charge or carry other tool with awlOnly Tools Matters
-
@Antti Lammi said:
Actually i have found alternative way for it but you need long bits from MUT and grind it to shape of awl, and you have full size removable awl.
It has few cons vs real awl
If it gets stuck bit cant be pulled out like regular awl cause bit stays on and it leaves from bit holder.
There is reason why many mod awl on wave/charge or carry other tool with awlOnly Tools Matters
Thanks, that’s definitely useful to know!

-
I did something similar to Anti; I ground to shape a n old, snapped, 7mm hex wrench. Too long to fit in tool, but short enough to travel in the pocket behind the hook panel on the sheath. And yes, it can dislodge from the exchanger, but then, I have the pliers right in my hand!!



-
@Juan el Boricua said:
I did something similar to Anti; I ground to shape a n old, snapped, 7mm hex wrench. Too long to fit in tool, but short enough to travel in the pocket behind the hook panel on the sheath. And yes, it can dislodge from the exchanger, but then, I have the pliers right in my hand!!
I love the wrapping you did on the two blades. That's a much better visual method for identifying which is which. What kind of thread did you use for that? It looks like what would be used for fly tying.
-
Thanks, Jason. Can't remember for what is used, but it's nylon. I did it more to help deploy the blades since I'm a lefty!!
-
@Juan el Boricua said:
I did something similar to Anti; I ground to shape a n old, snapped, 7mm hex wrench. Too long to fit in tool, but short enough to travel in the pocket behind the hook panel on the sheath. And yes, it can dislodge from the exchanger, but then, I have the pliers right in my hand!!
That’s a great idea - like the grinding work!
-
Thanks, Mr Vic!
Yeah, would be good but, I'm aware that it wouldn't be cost effective ( by corporate standards) and besides, what would happen to us modders and hackers!?!?!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
