Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Replacement cutters

Scheduled Pinned Locked Moved Gerber Tools
10 Posts 1 Posters 2.8k Views
  1. Home
  2. Tool Talk
  3. Gerber Tools
  4. Replacement cutters
Replacement cutters
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • SA Offline
    SA
    Posts: 15
    SA Offline
    SA
    wrote on last edited by
    Quote Reply

      Hi guys I just wanted to make a post showing that it is possible to make Gerber replacement cutters yourself with some tools and know how. We all know the carbide cutters are sub par. If you check Gerbers website the replacement cutters have a 1.5 star review..

      I didn’t use anything but some basic hand and power tools. Ideally i would use a milling machine but I didn’t have access to one. I used a standard Nicholson file. Heated it until it was cherry red. Let it cool. Ground it down with a 5” grinder to roughly 0.080”. I then sprayed layout blue on it and put my cutters down to outline them. My wife god bless her threw out the actual Gerber carbide cutters so I had to trace my replacement cutters I already made. They are not perfect looking but they work and you can sharpen them.

      I then drilled out the hole to 7/64 for the screw to fasten it to the plier head. After drilling I cut with an angle grinder the cutters out. If you’re not very proficient with an angle grinder I recommend using a hacksaw. One cut out I used a file to fit them into the plier head. I messed up on this one and had to grind one of the cutters a bit smaller. Doesn’t look right but she cuts like no ones business.

      Once cut and shaped I fired up the torch again and heated them red hot until no longer magnetic. I then stuck them in an oven set to 325 degrees for 15 minutes to temper them.

      This is the second set I’ve made and while not the easiest to make it only took about 1.5 hours start to finish. I understand not everyone will be willing or able to do this but if those replaceable cutters drove you insane like they did me. I wanted to share that it is totally do able and while I could make Leatherman cutters for my surge the Gerber ones are much easier to replicate.

      They cut thick steel coat hangers and nails without cracking or being destroyed. The edge is hard and with a diamond file can be retouched many many times.

      I hope you guys liked the post. This was my first forum post.

      I have many pictures and a video but it won’t let me post them. Any help??

      Thanks for reading.

      Scott

      1 Reply Last reply
      • CarbideCruzer Offline
        CarbideCruzer
        Posts: 164
        CarbideCruzer Offline
        CarbideCruzer
        wrote on last edited by
        #1 Quote Reply

          As much as I am a fan of the USA made Gerber knives and USA made with global materials Gerber multi tools, even I am not a fan of the replaceable cutters. While I do genuinely appreciate the carbide Gerber sources is domestically made and by and large the all American made Gerber Center Drive Plus is a great tool, the cutters are a detriment to this tool.

          To answer your question in regards to posting images, merely type in any search engine without the quotations "image uploader". This forum uses BB code, otherwise known as bulletin board code. I'll provide an image to showcase what you'll want to see and how to do this.

          Notice the [](http://and the uniform resource locator (URL) text juxtaposed to the image text. Essentially to upload you need the URL and image set in the [url) and There are host of sites to upload images without any financial cost. Just note that your individual internet protocol is being recorded, so I do advise to take that into consideration.

          Edit: So this will not let me show the url text and other text. All you need to know is to make sure this is written in BB code.

          1 Reply Last reply
          • Juan el Boricua Offline
            Juan el Boricua
            Posts: 4,111
            Juan el Boricua Offline
            Juan el Boricua
            wrote on last edited by
            #2 Quote Reply

              Welcome, SA, to :MTO:!
              Thanks for the tutorial since I, for once, will like to have a more durable replacement.
              :like:
              :cheers:

              1 Reply Last reply
              • SA Offline
                SA
                Posts: 15
                SA Offline
                SA
                wrote on last edited by
                #3 Quote Reply

                  Carbidecruzer that sounds like a ton of work.

                  Juan it is definitely doable and I’m loving it made the Center Drive my current favourite.

                  1 Reply Last reply
                  • CarbideCruzer Offline
                    CarbideCruzer
                    Posts: 164
                    CarbideCruzer Offline
                    CarbideCruzer
                    wrote on last edited by
                    #4 Quote Reply

                      Utilizing any search engine; DuckDuckGo, Startpage or any search engine for that matter type in the words image up loader. You'll see multiple variations, but the concept is to upload an image and using Bulletin Board code, this is how one can see the images.

                      There is synergy between the uniform resource locator and Bulletin Board code, so that aspect is already administrated.

                      1 Reply Last reply
                      • SteveC Offline
                        SteveC
                        Global Moderators
                        Posts: 73,535
                        SteveC Offline
                        SteveC
                        Global Moderators
                        wrote on last edited by
                        #5 Quote Reply

                          Welcome to the forum SA :cheers:

                          we would love to see some pics of your cutters.

                          CC makes it sound more complicated that it needs to be. There is a lot of info here about posting pics

                          /topic/2306

                          By far the easiest way is to use a host site like imgur, that is what most of us do here on the forum for pics. You can use the attach feature as well but you have to reduce the size of the file to below 512KB using an image resizer.

                          Just stay away from Photobucket as it sucks.

                          1 Reply Last reply
                          • CarbideCruzer Offline
                            CarbideCruzer
                            Posts: 164
                            CarbideCruzer Offline
                            CarbideCruzer
                            wrote on last edited by
                            #6 Quote Reply

                              Hard to say if these inserts will fit precisely with any Gerber, let alone any multi tool, let alone how well these will cut, yet I did find two domestic alternatives to the Gerber carbide inserts.

                              Insert, TCMW-2-1.5-1 HSS

                              20 degree relief

                              These are made out of high speed steel as well.

                              1 Reply Last reply
                              • SteveC Offline
                                SteveC
                                Global Moderators
                                Posts: 73,535
                                SteveC Offline
                                SteveC
                                Global Moderators
                                wrote on last edited by SteveC
                                #7 Quote Reply

                                  @CarbideCruzer said:
                                  Hard to say if these inserts will fit precisely with any Gerber, let alone any multi tool, let alone how well these will cut, yet I did find two** domestic alternatives **to the Gerber carbide inserts.

                                  Insert, TCMW-2-1.5-1 HSS

                                  20 degree relief

                                  These are made out of high speed steel as well.

                                  Remember this is an international forum. The OP is from Canada ;)

                                  1 Reply Last reply
                                  • CarbideCruzer Offline
                                    CarbideCruzer
                                    Posts: 164
                                    CarbideCruzer Offline
                                    CarbideCruzer
                                    wrote on last edited by
                                    #8 Quote Reply

                                      @SteveC said:
                                      Remember this is an international forum. The OP is from Canada ;)

                                      Allow me to clarify. Those two inserts I mentioned as domestic mean they are made in United States of America. At the time of the posting, the thread creator had no indication of where he was from. Either way, I bought those two inserts and out of the box these did not cut anything. My best guess is because for lack of better nomenclature is there is a lack of "cutting edge inclination".

                                      Perhaps the methodologically of using a file may work, I've yet to try this personally. This is unlikely at this time, yet perhaps Gerber may alter the replacement cutter metallurgy.

                                      1 Reply Last reply
                                      • cody6268 Offline
                                        cody6268
                                        Posts: 6,250
                                        cody6268 Offline
                                        cody6268
                                        wrote on last edited by
                                        #9 Quote Reply

                                          Gerber has 154CM in their blade stock, given the Applegate Covert, the Gator 154CM, and the Combat folder and fixed blade all use this steel ,and are made in the USA. They could very easily swap from "Carbide" to 154CM if they wanted to. I wonder why not? Last time I checked, Gerber and LM cutters cost the same to buy replacements. Just the LM cutters won't get damaged unless one cuts a live electrical wire, or too hard/thick a steel wire. Only time I dinged an LM cutter was their fault, my ST300 had been broken when I loaned it out, and it came back from Portland with cutters that wouldn't cut, and didn't appear hardened correctly. The replacements I bought worked fine. My MP600ST cutters already show slight chipping from light use--rebar binding wire.

                                          1 Reply Last reply

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login

                                          1. Home
                                          2. Tool Talk
                                          3. Gerber Tools
                                          4. Replacement cutters
                                          Reply
                                          • Reply as topic
                                          Log in to reply
                                          COMMUNITY LINKS
                                          EDC-TV SAKWiki GearFeed SAKSelector
                                          Operational Funds

                                          Help us keep the Unworkable working!

                                          Make A Donation
                                          November Goal: $300.00
                                          Due Date: Nov 30
                                          Total Receipts: $0.00
                                          Below Goal: $300.00
                                          0% funded
                                          • Login

                                          • Don't have an account? Register

                                          • Login or register to search.
                                          • First post
                                            Last post
                                          0