Drilling SAK tools...
-
Are you using a press? Carbide bits?
-
I’ve used a press and hand held with cobalt and steel bits so far and nothing even touches it. I’ve tried slow start with as much pressure as I dare on the small bit and fast too. Maybe I have work hardened it inadvertently?
-
Kamikiri
Maybe a job but for Goldfinger’s laser?
I’m with carbide bits.
Saw a pretty informative thread over on Blade Forum
Here is the link.
https://www.bladeforums.com/threads/how-to-drill-hardened-steel.794728/
It is a challenge for sure.
-
The problem is that the can opener is already hardened steel, around 52 HRC IIRC. It's possible to drill it, but I would think carbide bits and a drill press would be in order.
You might want to check out the Mod Squad sub-forum and see how others have handled it...
https://forum.multitool.org/index.php/board,16.0.html -
I bored a larger opening in SAK scissors with a Dremil and diamond bit. Took a long time but I got it done.
-
I’m essentially going to systematically try all of these until I get through! I’ll report back if I get any luck...

-
Slow and easy and lots of cooling but it can be done with less than perfect tools. I used small diameter diamond bits then moved up in diameter till I reached the size I was happy with.
-
Okay I got through in the end with a tungsten carbide end mill in my drill press. Actually went through the steel like butter but still not as easy at it sounds.
It may be because they were cheap bits or just because they are such small diameter or my cooling wasn't efficient enough but literally any catching (especially if pushing too hard or as it exited the other side) and the bits just shattered like glass.
The reason I actually wanted to drill this in the first place was to insert a stud to keep a can opener modified to a full on gut hook slightly higher in the frame. The hook part of the can opener, as you probably know, is what stops it in the frame when it hits the spring. To be fair the nail nick was still accessible with it removed but just sat slightly low and you know how it is when you get a bee in your bonnet about these things.
Actually looks quite cool in the end but at the cost of two mill bits and two taps probably not something I'm going to be trying in my garage again any time soon ;0)




-
Great mod!
-
Cool tool mod.

-
Very neat!

-
Is it easy to use? It looks to be recessed very deep in the scales.

-
Nice work chap, beautifully executed

-
@pfrsantos said:
Is it easy to use? It looks to be recessed very deep in the scales.

Thanks everyone. The stud is just to stop the blade dropping to far into the frame (due to the bottom of the opener being removed) making the nail nick inaccessible so not used for opening the blade as such. So yes, work perfectly for that ;0)
-
@Helvetica Bold said:
Thanks everyone. The stud is just to stop the blade dropping to far into the frame (due to the bottom of the opener being removed) making the nail nick inaccessible so not used for opening the blade as such. So yes, work perfectly for that ;0)Nice to see you got it done! Congrats!
Nice part about your thumb stud/position holder, is that now you can trim down the opening side where the can opener hook used to be...as much as you like.
-
@kamakiri said:
Nice to see you got it done! Congrats!Nice part about your thumb stud/position holder, is that now you can trim down the opening side where the can opener hook used to be...as much as you like.
Exactly that. The gut hook works with it there but taking it off makes it more usable even if you can’t open cans with it anymore :0)
-
Maybe Felix is watching again!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

What a lovely mod!