Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Need pin stock

Scheduled Pinned Locked Moved Swiss Army Knights Forum
6 Posts 1 Posters 1.1k Views
  1. Home
  2. Tool Talk
  3. Swiss Army Knights Forum
  4. Need pin stock
Need pin stock
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • DavZell Offline
    DavZell
    Posts: 308
    DavZell Offline
    DavZell
    wrote on last edited by
    Quote Reply

      Good morning, fellow SAK'ers. I am doing some modding on 91mm SAK's. The pin stock I've gotten is of poor quality compared to what I used on my first mod, despite being from the same supplier (which I admit was no-brand). It bends instantly when peening. Both diameters (smaller and larger) perform the same, yet I had no problems with either size before, so I don't think it is my technique. They also bend in hand much easier than the last piece from before. It could be quality, brass content, or level of hardening, I suppose.

      Anyway, I am in need of pin stock, preferably from a US source so it doesn't take too long, and of a known good, consistent quality.

      Can anyone help me out?

      Thanks,
      David

      1 Reply Last reply
      • Explorer Offline
        Explorer
        Posts: 1,794
        Explorer Offline
        Explorer
        wrote on last edited by
        #1 Quote Reply

          I’m in the same boat- looking for some good quality brass rod stock for mods. Finding the 2.5 mm seems much easier than finding the 2.2 mm. A good US based source for both sizes would be awesome however I’ve yet to find one That carries both sizes. But I have not searched high and wide as of yet.

          I found this 2.5 mm brass rod stock on Amazon made by K&S Precision Metals it’s 2.5mm Diameter X 300mm Long, 4 Pieces per Pack, Made in The USA (i’m not sure if it’s OK to post links to things on Amazon let me know if it’s OK and I will) here is a pic of it.

          I’m wondering if anyone has experience with this brand or could possibly recommend a better source for some good brass stock as well so I’ll just be here eating some popcorn don’t mind me...
          :popcorn:

          FFC20B9D-9DB6-4EC1-B59F-00A4C2820FF7.jpeg

          Merit Badges
          Chuck Yeager Challenge MiniChamp 30 day Challenge Camper 30 day Challenge SAK STACK Challenge 30 Days  30 Day Vintage SAK Challenge 30 Day TWEEN Challenge - 84 and 85mm SAKs Alox Addict Challenge Discontinued SAK/MT Challenge  Classic 30 Day Challenge 30 Day Fire starting Challenge 30 Day Flashlight Challenge MTo Anniversary Challenge MacGyver 30 Day Challenge
          1 Reply Last reply
          • Mike 56 Offline
            Mike 56
            Posts: 1,705
            Mike 56 Offline
            Mike 56
            wrote on last edited by
            #2 Quote Reply

              .I have been using K and S brass rod it’s pretty hard that makes it hard to peen. Next knife I mod I am going heat the rod with a torch and let it cool to soften the rod.

              Merit Badges
              Scale Changer
              1 Reply Last reply
              • DavZell Offline
                DavZell
                Posts: 308
                DavZell Offline
                DavZell
                wrote on last edited by
                #3 Quote Reply

                  @Mike 56 said:
                  .I have been using K and S brass rod it’s pretty hard that makes it hard to peen. Next knife I mod I am going heat the rod with a torch and let it cool to soften the rod.

                  I would be careful about softening too much, as you may face my issue. I'm not sure if mine are soft or just not the right/best quality/composition.

                  Let us know how it goes.

                  1 Reply Last reply
                  • Explorer Offline
                    Explorer
                    Posts: 1,794
                    Explorer Offline
                    Explorer
                    wrote on last edited by
                    #4 Quote Reply

                      @Mike 56 said:
                      .I have been using K and S brass rod it’s pretty hard that makes it hard to peen. Next knife I mod I am going heat the rod with a torch and let it cool to soften the rod.

                      Thanks for that Mike very helpful information
                      :cheers:

                      Merit Badges
                      Chuck Yeager Challenge MiniChamp 30 day Challenge Camper 30 day Challenge SAK STACK Challenge 30 Days  30 Day Vintage SAK Challenge 30 Day TWEEN Challenge - 84 and 85mm SAKs Alox Addict Challenge Discontinued SAK/MT Challenge  Classic 30 Day Challenge 30 Day Fire starting Challenge 30 Day Flashlight Challenge MTo Anniversary Challenge MacGyver 30 Day Challenge
                      1 Reply Last reply
                      • knifecoop Offline
                        knifecoop
                        Posts: 310
                        knifecoop Offline
                        knifecoop
                        wrote on last edited by
                        #5 Quote Reply

                          One option, if you have the tools, is to take an oversize rod stock and turn it down to fit. This can be done quite nicely using a metal lathe. In a pinch a simple way is to mount a short piece of pin stock in a drill and run it turning the opposite way against a running belt grinder, you can carefully sand it down to fit. Note this takes some practice to have consistent results, but will work.

                          Merit Badges
                          Modified SAK Challenge Explorer 30 Day Challenge Discontinued SAK/MT Challenge  30 Day Vintage SAK Challenge
                          1 Reply Last reply

                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                          With your input, this post could be even better 💗

                          Register Login

                          1. Home
                          2. Tool Talk
                          3. Swiss Army Knights Forum
                          4. Need pin stock
                          Reply
                          • Reply as topic
                          Log in to reply
                          COMMUNITY LINKS
                          EDC-TV SAKWiki GearFeed SAKSelector
                          Operational Funds

                          Help us keep the Unworkable working!

                          Make A Donation
                          November Goal: $300.00
                          Due Date: Nov 30
                          Total Receipts: $0.00
                          Below Goal: $300.00
                          0% funded
                          • Login

                          • Don't have an account? Register

                          • Login or register to search.
                          • First post
                            Last post
                          0