Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

wire cutter abuse

Scheduled Pinned Locked Moved General Tool Discussion
7 Posts 1 Posters 1.6k Views
  1. Home
  2. Tool Talk
  3. General Tool Discussion
  4. wire cutter abuse
wire cutter abuse
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • scrappy Offline
    scrappy
    Posts: 2,633
    scrappy Offline
    scrappy
    wrote on last edited by
    Quote Reply

      I was adding a pocket clip to my shrade tradesman shears and needed something to cut the cli down to size with. on me I had a wave and adjustable shrade tool. I used the shcrade to start cutting the pocket clip it made the cut with extreme force but took no damage. however some of the angles with the clip in between the pliers kept the cutters from being able to cut the clip because the nose of the plier was already closed as tight as it could with the clip in the middle. I used my wave to make the cut just fine but it did cause a little damage to the cutters. I then try to cut a piece of the clli that was not flat but angled. the wave pliers bent around the clip and the needle nose ends were twisted, one to the left and one to the right. so I stopped that and used the old wave diamond file to fix the cutter and take the flat spots out. I used a swiss tool to cut the angled area and it did what the wave could not. it cut it but it tool even more damage than the wave did. probably because the plier didn't flex at all but instead took all that force on the wire cutters. after using the diamond file it is much better now. I cut up another pocket clip. the powerlock made the cuts even at an angle. way to go sog and it took the least damage. the most comfortable to use in this was the charge but the sog is clearly the winner. unfortunatly the file sucks and it couldn't help fix the other tools so once again leatherman has another advantage over the sog tool.
      yet I was so impressed with the sog that I added a pocket clip for it also. great pliers.
      do you think there is any leatherman that could cut this stuff better than the charge or would they all have the swame problem with the wire cutters flexing away from each other?

      1 Reply Last reply
      • rockyman500 Offline
        rockyman500
        Posts: 531
        rockyman500 Offline
        rockyman500
        wrote on last edited by
        #1 Quote Reply

          SURGE

          [

          1 Reply Last reply
          • J-sews Offline
            J-sews
            Admin Team
            Posts: 23,224
            J-sews Offline
            J-sews
            Admin Team
            wrote on last edited by
            #2 Quote Reply

              @rockyman500 said:
              SURGE

              Or maybe the Core?

              Actually I am surprised that any of the tools cut through, as pocket clips are usually made of extremely tough spring steel. Kudos to the SOG tool :salute:

              In order to be certain of having the right tool for every job.........one must first acquire a lot of tools

              1 Reply Last reply
              • scrappy Offline
                scrappy
                Posts: 2,633
                scrappy Offline
                scrappy
                wrote on last edited by
                #3 Quote Reply

                  I tried the core and it is a no go.
                  the soft wire cutters on the leatherman are thinner than the sog so I wondered if that had something to do with it. I got my new sog out. it has thinner cutterd also and couldn't make the cut either. the pliers flexed. I pulled the old sog out again and it did it. I don't know it is just this one tool that can do it or if the older models would all handle it better.I have been using this tool for years and the cuttes were already dulled but wether that made a difference or perhaps the gears help and the older model has a thicker wire cutter...

                  1 Reply Last reply
                  • Sean Offline
                    Sean
                    Posts: 3,274
                    Sean Offline
                    Sean
                    wrote on last edited by Sean
                    #4 Quote Reply

                      Would a variable speed angle grinder with cutoff disk do the trick? You'd have to watch the heat but on a clip it might not be so critical. I know where all looking for that all special tool that does the imaginable but hey... I broke my surge jaws twisting a piece of heavy spring type steel. Much heavier, thicker, or harder than say antenna wire made of spring steel I personally wouldn't attempt it with a multi-tool.

                      sean

                      1 Reply Last reply
                      • NeitherExtreme Offline
                        NeitherExtreme
                        Posts: 1,957
                        NeitherExtreme Offline
                        NeitherExtreme
                        wrote on last edited by
                        #5 Quote Reply

                          @J-sews said:
                          Actually I am surprised that any of the tools cut through, as pocket clips are usually made of extremely tough spring steel. Kudos to the SOG tool :salute:

                          That's what I was thinking as well, since MTs are mostly made to cut copper. I'd be looking for a dedicated cutters for a job like that.

                          1 Reply Last reply
                          • scrappy Offline
                            scrappy
                            Posts: 2,633
                            scrappy Offline
                            scrappy
                            wrote on last edited by
                            #6 Quote Reply

                              ya the charge actally did better than the core.I cut some zip ties today to see if ther was permanent damage and the core folds the zip ties now instead of cutting them.

                              1 Reply Last reply

                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                              With your input, this post could be even better 💗

                              Register Login

                              1. Home
                              2. Tool Talk
                              3. General Tool Discussion
                              4. wire cutter abuse
                              Reply
                              • Reply as topic
                              Log in to reply
                              COMMUNITY LINKS
                              EDC-TV SAKWiki GearFeed SAKSelector
                              Operational Funds

                              Help us keep the Unworkable working!

                              Make A Donation
                              November Goal: $300.00
                              Due Date: Nov 30
                              Total Receipts: $0.00
                              Below Goal: $300.00
                              0% funded
                              • Login

                              • Don't have an account? Register

                              • Login or register to search.
                              • First post
                                Last post
                              0