Working Ti.
-
What about bending. Can it be done easy. Do I have to soften it?
-
Nope, the handles on the Charge are extremely durable and hard wearing.. I like how they don't show scratches..
-
Clarification: titanium barstock is supplied in an "annealed" condition, which means it is relatively soft and able to be machined. Annealed titanium bends quite readily. It can then be heat treated to a harder condition, as I'm sure the Charge scales are.
John, will you be working with raw titanium barstock? Or is it pieces of titanium scavenged from other finished products?
-
@J-sews said:
Clarification: titanium barstock is supplied in an "annealed" condition, which means it is relatively soft and able to be machined. Annealed titanium bends quite readily. It can then be heat treated to a harder condition, as I'm sure the Charge scales are.John, will you be working with raw titanium barstock? Or is it pieces of titanium scavenged from other finished products?
Can any titanium be heat treated or is it just certain alloys?
-
Clarification: titanium barstock is supplied in an "annealed" condition, which means it is relatively soft and able to be machined. Annealed titanium bends quite readily. It can then be heat treated to a harder condition, as I'm sure the Charge scales are.
John, will you be working with raw titanium barstock? Or is it pieces of titanium scavenged from other finished products?
Can any titanium be heat treated or is it just certain alloys?
I don't know. :-\
I do know that the titanium most of us encounter is 6al4v grade.
-
I will have to check today. I have the slip at work and will get it.
-
Regarding the polishing to a mirror finish, what's the best way of going about that?
I have a Ti to play with with a hand brushed finish from me removing an ugly anodising job. Have dremel, will play! Should I try a polishing felt and some jewellers rouge?
-
@nuphoria said:
Regarding the polishing to a mirror finish, what's the best way of going about that?I have a Ti to play with with a hand brushed finish from me removing an ugly anodising job. Have dremel, will play! Should I try a polishing felt and some jewellers rouge?
A Charge Ti? And you've already smoothed up the rough cast finish a bit? (because a smooth finish is important before beginning to polish)
As regards the Dremel/felt/jewelers rouge, you may need a bit more horsepower than that. :-\ Give it a try and see, but chances are you'll need a bench grinder with a 6" rag wheel to really cut through all the blemishes and leave a mirror finish.

-
Thanks, perhaps I'll stick a big felt bit in my makita drill - that might ramp it up a bit!
Otherwise this means I have an excuse to buy a bench grinder, which is something I have always had my eye on
-
I've polished a knife blade and a flashlight with dremel, it works albeit slowly, you just have to crank up the speed so the felt pad isn't bogged down by friction.
-
Ti <u>Spork</u> I meant to say... thanks for the advice, I shall start messing with it tomorrow.
(Disclaimer: I leave out words and come out with erroneous spellings due to dyslexia)
-
The flashlight I polished: http://img174.imageshack.us/img174/1873/vichg4.jpg
Turned out to be a bad idea thou, aluminum stay polished for a day, then get scratched to hell.
-
Yeah, I've found that with white gold, it doesn't stay shiny for long on my hands!
You did a lovely job though
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
