Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Sharpening methods

Scheduled Pinned Locked Moved General Tool Discussion
67 Posts 1 Posters 5.2k Views
  1. Home
  2. Tool Talk
  3. General Tool Discussion
  4. Sharpening methods
Sharpening methods
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • chip Offline
    chip
    Posts: 1,531
    chip Offline
    chip
    wrote on last edited by
    #60 Quote Reply

      @pfrsantos said:
      That's what kitchen knives and Opinels are for.

      :pok: :pok:

      And even better if you can learn on other peoples kitchen knives like I did :rofl:

      1 Reply Last reply
      • AzteCypher Offline
        AzteCypher
        Posts: 4,051
        AzteCypher Offline
        AzteCypher
        wrote on last edited by
        #61 Quote Reply

          I actually do have a few I can practice on. Need to make time this weekend.

          1 Reply Last reply
          • chip Offline
            chip
            Posts: 1,531
            chip Offline
            chip
            wrote on last edited by
            #62 Quote Reply

              @AzteCypher said:
              I actually do have a few I can practice on. Need to make time this weekend.

              :tu: practice makes perfect.

              1 Reply Last reply
              • chip Offline
                chip
                Posts: 1,531
                chip Offline
                chip
                wrote on last edited by
                #63 Quote Reply

                  Also when using the worksharp elite it creates a good burr due to the fact you are sharpening edge trailing. Which is really helpful because you can literally watch it form once you hit the edge as you make a pass.

                  I am getting better at stropping but no way as good as I would like to be, so found making a few passes on a very fine ceramic rod was excellent at knocking off the burrs.

                  1 Reply Last reply
                  • Mike 56 Offline
                    Mike 56
                    Posts: 1,705
                    Mike 56 Offline
                    Mike 56
                    wrote on last edited by
                    #64 Quote Reply

                      Try using a light oil on your diamond stones it cleans and keeps them from getting plugged up. They work a lot better with oil. I use WD-40 because I buy it buy it by the gallon. I use cutting board oil on knives with wood scales it is a thin mineral oil it looks like it would work well. The three biggest mistakes people make stopping is the wrong angle it is better to start with less angle all flat. As you are finishing a pass on a strop or stone do not let the tip of the blade leave the stone or the strop. when stropping use very light pressure. A rubber mouse pad is much more forgiving than a leather strop.

                      1 Reply Last reply
                      • chip Offline
                        chip
                        Posts: 1,531
                        chip Offline
                        chip
                        wrote on last edited by
                        #65 Quote Reply

                          I use glass cleaner (nilglass) as a lapping fluid when using my diamond plates to stop them from clogging.
                          And then a quick spray and wipe down when I am done keeps them clean.
                          Also any glass cleaner residue left behind evaporates much quicker than water. Never had any problems with rust.

                          I too use chopping board oil on all my knives as it’s very cheap and food safe.

                          1 Reply Last reply
                          • Sos24 Offline
                            Sos24
                            Global Moderators
                            Posts: 11,507
                            Sos24 Offline
                            Sos24
                            Global Moderators
                            wrote on last edited by
                            #66 Quote Reply

                              @David Bowen said:
                              I've yet to check out a DMT Aligner, maybe this fall I'll get the chance. It's similar in function to the Lansky/Gatco I feel. DMT makes good products, I hear people complain about quality from time to time but nothing crazy.

                              Sent from my SM-G996U using Tapatalk

                              It is very similar to both Lansky and Gatco. I had picked up at a state fair after a demonstration and just find it works for my needs. I’ve thought of trying the Lansky, but because of the similarities just wasn’t sure how much I’d can.

                              1 Reply Last reply

                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                              With your input, this post could be even better 💗

                              Register Login

                              1. Home
                              2. Tool Talk
                              3. General Tool Discussion
                              4. Sharpening methods
                              Reply
                              • Reply as topic
                              Log in to reply
                              COMMUNITY LINKS
                              EDC-TV SAKWiki GearFeed SAKSelector
                              Operational Funds

                              Help us keep the Unworkable working!

                              Make A Donation
                              November Goal: $300.00
                              Due Date: Nov 30
                              Total Receipts: $0.00
                              Below Goal: $300.00
                              0% funded
                              • Login

                              • Don't have an account? Register

                              • Login or register to search.
                              • First post
                                Last post
                              0