Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Howdy

Scheduled Pinned Locked Moved General Tool Discussion
3 Posts 1 Posters 598 Views
  1. Home
  2. Tool Talk
  3. General Tool Discussion
  4. Howdy
Howdy
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • ? This user is from outside of this forum
    Guest
    Posts:
    ? This user is from outside of this forum
    Guest
    wrote on last edited by
    Quote Reply

      Does anyone know of a bit driver that would fit in the keybar? I've been looking online for the last few days and I'm completely stumped? Can be micro bits, full sized bits, leatherman bits!

      1 Reply Last reply
      • Grant Lamontagne Offline
        Grant Lamontagne
        administrators
        Posts: 67,980
        Grant Lamontagne Offline
        Grant Lamontagne
        administrators
        wrote on last edited by
        #1 Quote Reply

          Welcome to the forum!

          I checked the Keybar and Keysmart websites and didn't see any bit drivers that either manufacturer had, and I can't think of any off the top of my head that would be available easily or sensibly.

          That having been said, if I was looking for a bit driver to fit one, I would probably look at the Leatherman flattened bits and a driver from a Wave- or rather the same driver that is on the Wave and many other Leatherman models. I'd find a cheapo that is otherwise trashed and salvage the driver.

          The reason I think I'd use that one (which is shocking to most members because I am very vocal about how much I HATE the Leatherman flat bits :facepalm:) is that the bit driver has broad, flat sides and I think that would work best with the Keybar. Its also slightly shorter than a regular type key, sonot should fit in well enough, and not be too wide as to require the expansion screws. I think it would be about as wide as two regular keys.

          I think that the driver from something like a Cybertool, or Gerber Center Drive would be far too bulky to fit nicely in the Keybar. The only concern is have about the Leatherman flat bit driver would be the size of the pivot hole- some modifications may be necessary to make that fit properly, but I'm sure it could be drilled out if the hole is too small, or filled with epoxy and a new hole drilled if it's too big.

          Make sure to keep us updated on what you do- I know I'll find the results fascinating!

          Def


          1 Reply Last reply
          • Poncho65 Offline
            Poncho65
            Global Moderators
            Posts: 88,523
            Poncho65 Offline
            Poncho65
            Global Moderators
            wrote on last edited by
            #2 Quote Reply

              Welcome to :MTO: :cheers:

              I am.thinkoing someone here at MTO has put a LM Bit Driver from a Wave into a Keybar :think:

              Maybe search in the Mod Squad sub forum down below the General Forum :think:

              Good luck with the search and I hope you find something that works for you :tu: :like:

              1 Reply Last reply

              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

              With your input, this post could be even better 💗

              Register Login

              1. Home
              2. Tool Talk
              3. General Tool Discussion
              4. Howdy
              Reply
              • Reply as topic
              Log in to reply
              COMMUNITY LINKS
              EDC-TV SAKWiki GearFeed SAKSelector
              Operational Funds

              Help us keep the Unworkable working!

              Make A Donation
              November Goal: $300.00
              Due Date: Nov 30
              Total Receipts: $0.00
              Below Goal: $300.00
              0% funded
              • Login

              • Don't have an account? Register

              • Login or register to search.
              • First post
                Last post
              0