Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

core driver on SURGE

Scheduled Pinned Locked Moved The Mod Squad
8 Posts 1 Posters 3.7k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. core driver on SURGE
core driver on SURGE
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • rockyman500 Offline
    rockyman500
    Posts: 531
    rockyman500 Offline
    rockyman500
    wrote on last edited by
    Quote Reply

      Is it possible to put a core phillips driver on the SURGE by removing the bit driver?

      1 Reply Last reply
      • nelly1974 Offline
        nelly1974
        Posts: 1,404
        nelly1974 Offline
        nelly1974
        wrote on last edited by
        #1 Quote Reply

          i am suprised no one has answered this question.

          1 Reply Last reply
          • Pacu Offline
            Pacu
            Posts: 5,782
            Pacu Offline
            Pacu
            wrote on last edited by
            #2 Quote Reply

              i say no as there is not enough room....but i'm no expert on modding

              Merit Badges
              MTo Anniversary Challenge LM Wave Challenge Jack'O Lantern Badge Buck 30 Day Challenge 30 Day Combo Edge Challenge
              1 Reply Last reply
              • Pacu Offline
                Pacu
                Posts: 5,782
                Pacu Offline
                Pacu
                wrote on last edited by
                #3 Quote Reply

                  and i was looking at my surge to make sure.

                  Merit Badges
                  MTo Anniversary Challenge LM Wave Challenge Jack'O Lantern Badge Buck 30 Day Challenge 30 Day Combo Edge Challenge
                  1 Reply Last reply
                  • max6166 Offline
                    max6166
                    Posts: 1,547
                    max6166 Offline
                    max6166
                    wrote on last edited by
                    #4 Quote Reply

                      Maybe the Blast driver then? Is it any narrower?

                      1 Reply Last reply
                      • gafftapegreenia Offline
                        gafftapegreenia
                        Posts: 1,093
                        gafftapegreenia Offline
                        gafftapegreenia
                        wrote on last edited by
                        #5 Quote Reply

                          I don't think its an issue of width, as the phillips and the bit holder are the same, but of length.

                          1 Reply Last reply
                          • prime77 Offline
                            prime77
                            Posts: 2,887
                            prime77 Offline
                            prime77
                            wrote on last edited by
                            #6 Quote Reply

                              Alright having thought this over for a while now and after putting a Kick driver on my Wave/topic/4579. I decided to give it ago and see if I could accomplish this. But surprisingly I have discovered that both the Core driver and the Kick/Fuse/Blast won't work on the Surge. Here are the problems that I ran into.

                              First off the main problem is that Core driver is much thinner at the base that the Surge bit driver. You would have to add washers to get the fit right. Then it's just to long to fit into the Surge. Even bending the plier sleeping tab (that's what I like to call it) down there is no guarantee that the pliers will even be able to close.

                              That leaves the Kick/Fuse/Blast driver.

                              I thought it would be a simple switch like on the Wave. I was wrong this time around. I took out the Surge driver and put in the Kick/Fuse/Blast driver closed the handle back up and found that the phillips driver wouldn't stay locked open. The Surge lock wouldn't grab the cut-out and keep the phillips driver in the locked position. After some time fiddling with it I took out the K/F/B driver and compared it to the Surge bit driver. I found the there is more metal on the Surge driver where the lock engages.

                              You can see from this shot the extra metal of the Surge driver under the K/F/B driver.
                              So I just don't think it's possible this time around. Maybe someone else will find a way. But here are some shots of what might have been.


                              1 Reply Last reply
                              • nelly1974 Offline
                                nelly1974
                                Posts: 1,404
                                nelly1974 Offline
                                nelly1974
                                wrote on last edited by
                                #7 Quote Reply

                                  that looks good. there has to be someone here who has already done this. i would be very surprised if it hasn't.

                                  1 Reply Last reply

                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                  With your input, this post could be even better 💗

                                  Register Login

                                  1. Home
                                  2. Tool Talk
                                  3. The Mod Squad
                                  4. core driver on SURGE
                                  Reply
                                  • Reply as topic
                                  Log in to reply
                                  COMMUNITY LINKS
                                  EDC-TV SAKWiki GearFeed SAKSelector
                                  Operational Funds

                                  Help us keep the Unworkable working!

                                  Make A Donation
                                  November Goal: $300.00
                                  Due Date: Nov 30
                                  Total Receipts: $0.00
                                  Below Goal: $300.00
                                  0% funded
                                  • Login

                                  • Don't have an account? Register

                                  • Login or register to search.
                                  • First post
                                    Last post
                                  0