Single-wing Wingman
-
given that the drivers are likely to have a side load put on them and therefore need good retention but the things like the can opener will only ever be used force against the backstop, why not swap the ends round? Put the drivers where the tools normally go, and the other tools at the plier end.
Does anyone know how hard the file is compared to a "normal" Leatherman screwdriver? I'm thinking of attacking it to give it a usable, slender shank.
-
@zoidberg said:
What I failed to note before I did this was that the spring no longer held them shut.Well that reminds me of my first ever attempted hack - trying to make a Gerber Evo non-locking :ahhh. A complete fail but its not impossible the Gerber PE will make a reappearance in my Wi-man

Thanks for the great heads-up.
-
@Cupboard said:
given that the drivers are likely to have a side load put on them and therefore need good retention but the things like the can opener will only ever be used force against the backstop, why not swap the ends round? Put the drivers where the tools normally go, and the other tools at the plier end.Does anyone know how hard the file is compared to a "normal" Leatherman screwdriver? I'm thinking of attacking it to give it a usable, slender shank.
I was thinking the same about the can opener but doesn't lifting a possibly "stuck" tool require a degree of retention?
Funny you should ask about the "file" hardness. Was also thinking about that, I have a plan too, and had just done a test grind with a diamond burr. Not obviously harder or unworkable though maybe that is because it is thinner.
-
What I failed to note before I did this was that the spring no longer held them shut.
Well that reminds me of my first ever attempted hack - trying to make a Gerber Evo non-locking :ahhh. A complete fail but its not impossible the Gerber PE will make a reappearance in my Wi-man

Thanks for the great heads-up.
No problem mate.
Better others don't make the same mistake. -
given that the drivers are likely to have a side load put on them and therefore need good retention but the things like the can opener will only ever be used force against the backstop, why not swap the ends round? Put the drivers where the tools normally go, and the other tools at the plier end.
Does anyone know how hard the file is compared to a "normal" Leatherman screwdriver? I'm thinking of attacking it to give it a usable, slender shank.
I was thinking the same about the can opener but doesn't lifting a possibly "stuck" tool require a degree of retention?
Funny you should ask about the "file" hardness. Was also thinking about that, I have a plan too, and had just done a test grind with a diamond burr. Not obviously harder or unworkable though maybe that is because it is thinner.
You two might want to see this.

-
@zoidberg said:
I can see why others might like them but they're not for me.Yeah, I'm with you on this one mate
Both in stock form, and as this mod, I really can't connect with it. It's like the whole is worse than the sum of it's parts. Each individual feature is not too bad, but collectively I don't like them at all. I bought a Wingman for the scissors, and the rest of it is just sat in a box destined to never be utilised unless I decide to add some of the parts to a PST or something (I have been tempted to repurpose the package opener).As a pliers tool, the handles have pointy bits so you have to hold it the correct way round, but even then the handles are too splayed for comfort. As a knife based tool, the blade locks and the drivers don't - which is completely the reverse of what I'd want.
But yes ... I can see why it might appeal more to others who may have different priorities and preferences
-
given that the drivers are likely to have a side load put on them and therefore need good retention but the things like the can opener will only ever be used force against the backstop, why not swap the ends round? Put the drivers where the tools normally go, and the other tools at the plier end.
Does anyone know how hard the file is compared to a "normal" Leatherman screwdriver? I'm thinking of attacking it to give it a usable, slender shank.
I was thinking the same about the can opener but doesn't lifting a possibly "stuck" tool require a degree of retention?
Funny you should ask about the "file" hardness. Was also thinking about that, I have a plan too, and had just done a test grind with a diamond burr. Not obviously harder or unworkable though maybe that is because it is thinner.
You two might want to see this.

How can I ever reveal what mod I have just done to my Wingman "file"
. Not that I would have ever used it for prying but I do have in mind some gentle "driving".Fortunately this very moment a cheap knock-off keychain multifunction tool has arrived for serious paint tin opening.
-
@Cupboard said:
given that the drivers are likely to have a side load put on them and therefore need good retention but the things like the can opener will only ever be used force against the backstop, why not swap the ends round? Put the drivers where the tools normally go, and the other tools at the plier end.This was the same thing I was thinking, and changed my tool up last night.

Those with keen eyes might note that I had to take off the tip of the small serrated blade. Otherwise, it would close far enough that the tip could pass through the hole in the bottom of the handle, and I really didn't feel like owning a tool that let me stab myself. Also, I've put the Wingman's semi serrated blade on this, because I wanted the Sidekick's blade on my Wingman.
@Cupboard said:
Does anyone know how hard the file is compared to a "normal" Leatherman screwdriver? I'm thinking of attacking it to give it a usable, slender shank.I think zoidberg's link covers my recent experience. It IS hardened, but I don't know how much.
With this tool swap, I don't have much concern about no retention on the file/small driver or the (remains of) the small serrated blade. And honestly, I've tested can openers before with almost zero retention. It just slows the process down. Unlike with screw drivers where you can bust your knuckles if they collapse on you. This setup is much more to my liking.
-
It was your experience that had me thinking. You want the shaft to be tough and the tip to be hard otherwise that happens.
I think once I've sorted my insurance out, finished tidying my house, got some wrapping paper, picked up some boots for my mum... I might have a fiddle and see :)
@50ft-trad said:
As a pliers tool, the handles have pointy bits so you have to hold it the correct way round, but even then the handles are too splayed for comfort. As a knife based tool, the blade locks and the drivers don't - which is completely the reverse of what I'd want.I hadn't realised how played they are, but comparing them to my Rebar it's a huge difference!

And I agree about the drivers too.
I think it should be possible to reduce the splay slightly by grinding down a bit of the plier head backstop

-
@Cupboard said:
I think it should be possible to reduce the splay slightly by grinding down a bit of the plier head backstop
Exactly this.
I am confused by people's willingness to take these things completely apart to frankenstein them, sometimes at significant effort, but being unwilling to take one apart to make adjustments to the tool in mostly-stock configuration.
Also, I've tested before the force the drivers will take, and I have to intentionally TRY to get them to collapse when they have the spring retention. So, I've never felt locking was any kind of necessity.
-
@Lynn LeFey said:
@Cupboard said:
I think it should be possible to reduce the splay slightly by grinding down a bit of the plier head backstop
Exactly this.
I am confused by people's willingness to take these things completely apart to frankenstein them, sometimes at significant effort, but being unwilling to take one apart to make adjustments to the tool in mostly-stock configuration.
Also, I've tested before the force the drivers will take, and I have to intentionally TRY to get them to collapse when they have the spring retention. So, I've never felt locking was any kind of necessity.
It seems to me, that if you're going to go to the trouble of taking a tool apart, you might as well give it the full treatment to get it tailored to your needs, rather than just coax it from bloody awful to vaguely passable :D
As to the drivers .... never tried them to be perfectly honest. I don't like the handles anyway for the reasons mentioned above, so unless I think they'd be worth transferring to another tool to improve that instead, they'll just be slung in the junk box with contempt :P :D :D
-
@Lynn LeFey said:
@Cupboard said:
I think it should be possible to reduce the splay slightly by grinding down a bit of the plier head backstop
Exactly this.
I am confused by people's willingness to take these things completely apart to frankenstein them, sometimes at significant effort, but being unwilling to take one apart to make adjustments to the tool in mostly-stock configuration.
Also, I've tested before the force the drivers will take, and I have to intentionally TRY to get them to collapse when they have the spring retention. So, I've never felt locking was any kind of necessity.
The ends of the handles are pointy, that is a game killer for me.
It is a design flaw and should have been picked up in testing.Quite a few people did make adjustments to the tool.
Those who frankensteined do so to most tools anyway.
This was suppose to be a fun hack with discarded parts.A driver will collapse on you when you don't want it to.
Screw starts to cam out, push down a little bit harder you'll get it and bam your nuckles are history. -
I'm getting very worried .... me and the lobster seem to have started agreeing on things ... :ahhh :ahhh :ahhh
-
As far as I know, it's not available on the market yet. If it weren't for an accidental leak, I don't think we'd even know what it looks like yet.
-
So my new Wingman arrived allowing a closer inspection. Not going to proceed with the mod for the following main reason, the tools are not held closed with a positive detent. Maybe a groove could be ground and the spring leaf bent but the outcome is uncertain. Changing this tool from an inside tool design to outside tools is not for me.
The cutters still don't meet (unless you have hands like zoidberg
) so its going back for that reason. :( -
Again, “If it's worth doing, it's worth overdoing.”
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

