Single-wing Wingman
-
@Cupboard said:
I think it should be possible to reduce the splay slightly by grinding down a bit of the plier head backstop
Exactly this.
I am confused by people's willingness to take these things completely apart to frankenstein them, sometimes at significant effort, but being unwilling to take one apart to make adjustments to the tool in mostly-stock configuration.
Also, I've tested before the force the drivers will take, and I have to intentionally TRY to get them to collapse when they have the spring retention. So, I've never felt locking was any kind of necessity.
-
@Lynn LeFey said:
@Cupboard said:
I think it should be possible to reduce the splay slightly by grinding down a bit of the plier head backstop
Exactly this.
I am confused by people's willingness to take these things completely apart to frankenstein them, sometimes at significant effort, but being unwilling to take one apart to make adjustments to the tool in mostly-stock configuration.
Also, I've tested before the force the drivers will take, and I have to intentionally TRY to get them to collapse when they have the spring retention. So, I've never felt locking was any kind of necessity.
It seems to me, that if you're going to go to the trouble of taking a tool apart, you might as well give it the full treatment to get it tailored to your needs, rather than just coax it from bloody awful to vaguely passable :D
As to the drivers .... never tried them to be perfectly honest. I don't like the handles anyway for the reasons mentioned above, so unless I think they'd be worth transferring to another tool to improve that instead, they'll just be slung in the junk box with contempt :P :D :D
-
@Lynn LeFey said:
@Cupboard said:
I think it should be possible to reduce the splay slightly by grinding down a bit of the plier head backstop
Exactly this.
I am confused by people's willingness to take these things completely apart to frankenstein them, sometimes at significant effort, but being unwilling to take one apart to make adjustments to the tool in mostly-stock configuration.
Also, I've tested before the force the drivers will take, and I have to intentionally TRY to get them to collapse when they have the spring retention. So, I've never felt locking was any kind of necessity.
The ends of the handles are pointy, that is a game killer for me.
It is a design flaw and should have been picked up in testing.Quite a few people did make adjustments to the tool.
Those who frankensteined do so to most tools anyway.
This was suppose to be a fun hack with discarded parts.A driver will collapse on you when you don't want it to.
Screw starts to cam out, push down a little bit harder you'll get it and bam your nuckles are history. -
I'm getting very worried .... me and the lobster seem to have started agreeing on things ... :ahhh :ahhh :ahhh
-
As far as I know, it's not available on the market yet. If it weren't for an accidental leak, I don't think we'd even know what it looks like yet.
-
So my new Wingman arrived allowing a closer inspection. Not going to proceed with the mod for the following main reason, the tools are not held closed with a positive detent. Maybe a groove could be ground and the spring leaf bent but the outcome is uncertain. Changing this tool from an inside tool design to outside tools is not for me.
The cutters still don't meet (unless you have hands like zoidberg
) so its going back for that reason. :( -
Again, “If it's worth doing, it's worth overdoing.”
-
@pingu said:
So my new Wingman arrived allowing a closer inspection. Not going to proceed with the mod for the following main reason, the tools are not held closed with a positive detent. Maybe a groove could be ground and the spring leaf bent but the outcome is uncertain. Changing this tool from an inside tool design to outside tools is not for me.The cutters still don't meet (unless you have hands like zoidberg
) so its going back for that reason. :(You should at least try. It's about having some fun and a little problem solving. And in this case it is cheap.
-
So my new Wingman arrived allowing a closer inspection. Not going to proceed with the mod for the following main reason, the tools are not held closed with a positive detent. Maybe a groove could be ground and the spring leaf bent but the outcome is uncertain. Changing this tool from an inside tool design to outside tools is not for me.
The cutters still don't meet (unless you have hands like zoidberg
) so its going back for that reason. :(You should at least try. It's about having some fun and a little problem solving. And in this case it is cheap.
Agree, it is cheaper than Lego's and more fun.
-
-
Again, “If it's worth doing, it's worth overdoing.”
Did you make a bushing?
Yes, I made two, one for the blade one for the clip.
Got any pics of them?Nothing to shown really, :-[ I used two Teflon washers, filed down the outside diameter by hand until them fit in where they need to go, then use an Alox farmer to bore out inside diameter until the pivot pole fits in. (Skeletool doesn't have an awl). Also under the scale there is a plastic spacer, I filed that down to make room for the longer blade, and added another washer to compensate the increased thickness of the blade.
-
Now, THAT's a knife.
-
Wow! That's [emoji41]
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

