Single-wing Wingman
-
So my new Wingman arrived allowing a closer inspection. Not going to proceed with the mod for the following main reason, the tools are not held closed with a positive detent. Maybe a groove could be ground and the spring leaf bent but the outcome is uncertain. Changing this tool from an inside tool design to outside tools is not for me.
The cutters still don't meet (unless you have hands like zoidberg
) so its going back for that reason. :( -
Again, “If it's worth doing, it's worth overdoing.”
-
@pingu said:
So my new Wingman arrived allowing a closer inspection. Not going to proceed with the mod for the following main reason, the tools are not held closed with a positive detent. Maybe a groove could be ground and the spring leaf bent but the outcome is uncertain. Changing this tool from an inside tool design to outside tools is not for me.The cutters still don't meet (unless you have hands like zoidberg
) so its going back for that reason. :(You should at least try. It's about having some fun and a little problem solving. And in this case it is cheap.
-
So my new Wingman arrived allowing a closer inspection. Not going to proceed with the mod for the following main reason, the tools are not held closed with a positive detent. Maybe a groove could be ground and the spring leaf bent but the outcome is uncertain. Changing this tool from an inside tool design to outside tools is not for me.
The cutters still don't meet (unless you have hands like zoidberg
) so its going back for that reason. :(You should at least try. It's about having some fun and a little problem solving. And in this case it is cheap.
Agree, it is cheaper than Lego's and more fun.
-
-
Again, “If it's worth doing, it's worth overdoing.”
Did you make a bushing?
Yes, I made two, one for the blade one for the clip.
Got any pics of them?Nothing to shown really, :-[ I used two Teflon washers, filed down the outside diameter by hand until them fit in where they need to go, then use an Alox farmer to bore out inside diameter until the pivot pole fits in. (Skeletool doesn't have an awl). Also under the scale there is a plastic spacer, I filed that down to make room for the longer blade, and added another washer to compensate the increased thickness of the blade.
-
Now, THAT's a knife.
-
Wow! That's [emoji41]
-
@Lynn LeFey said:
@Kampfer said:
Agree, it is cheaper than Lego's and more fun.Ain't THAT the truth! Lego's are crazy expensive.
Also... Sidekick's are down to $18 at Home Depot!
Except in the UK Wingman is £30 and Sidekick £45 :ahhh. Must be an expensive karibiner. Too expensive to experiment with. Who here would buy Sidekick at £45 when Rebar is available for £50?
-
@Lynn LeFey said:
@Kampfer said:
Agree, it is cheaper than Lego's and more fun.Ain't THAT the truth! Lego's are crazy expensive.
Also... Sidekick's are down to $18 at Home Depot!
Except in the UK Wingman is £30 and Sidekick £45 :ahhh. Must be an expensive karibiner. Too expensive to experiment with. Who here would buy Sidekick at £45 when Rebar is available for £50?
Come on, think about how much money you will save from stop buying SAK in the future. ;)
-
I opened three cans with the can opener on my one-wing build. I have the can opener on the end with no retention other than the screw tightness, and it worked pretty well. The issue wasn't the tool folding so much as the fact that the can opener on the Wingman/Sidekick has a short cutting blade, so it's kind of slow, modded or not.
I also tried the small flathead driver on it today, and while it folded, it was while working on the faceplate of a light switch, so there was no force, and no damage. Not optimal, but acceptable. I'd rather the weak retention be on those tools instead of the main drivers.
-
@Lynn LeFey said:
@Kampfer said:
Agree, it is cheaper than Lego's and more fun.Ain't THAT the truth! Lego's are crazy expensive.
Also... Sidekick's are down to $18 at Home Depot!
Except in the UK Wingman is £30 and Sidekick £45 :ahhh. Must be an expensive karibiner. Too expensive to experiment with. Who here would buy Sidekick at £45 when Rebar is available for £50?
Agreed! a Rebar is several times as good as a Sidekick, and at very little cost difference over here
-
@Lynn LeFey said:
I opened three cans with the can opener on my one-wing build. I have the can opener on the end with no retention other than the screw tightness, and it worked pretty well. The issue wasn't the tool folding so much as the fact that the can opener on the Wingman/Sidekick has a short cutting blade, so it's kind of slow, modded or not.I also tried the small flathead driver on it today, and while it folded, it was while working on the faceplate of a light switch, so there was no force, and no damage. Not optimal, but acceptable. I'd rather the weak retention be on those tools instead of the main drivers.
I agree. -
Your SAK has TNT?

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



