Babola's Acid Wave project
-
Stage 1, acid wash completed. :)
What you see below is the raw surface finish as a result of ferric chloride etching into the surface of stainless steel. I'm glad there weren't any hiccups along the way and only a 15 min dip in an etchant was required.
This will now be cleaned and put in the tumbler for stone-washed effect. If I have time to do this tonight I will, if not then tomorrow morning.

I really like how the screw heads turned out. :)

Next step - stone tumbler.
-
That looks really nice. Is it as black as the photo's show?
Pete
-
Can't wait to see the next step mate :o.

-
@pietervn said:
That looks really nice. Is it as black as the photo's show?Pete
Hi Pete, nah it's actually more gray than anthracite as in my photos. Must be the combination of low exposure and wrong white balance. I'll try posting more correctly exposed photos next time. :P
@Top-Gear-24 said:
Can't wait to see the next step mate :o.
Sure, I'm just thinking I could do the next step now, but tumbling is noisy (I do part by hand part in a dryer) and it's almost 11PM here now :(
The sheer excitement may get the best of me, though :P -
I'd realized this before, but seeing the Wave disassembled just drives home how complex and difficult to manufacture the handles of the Wave are. Just imagining the accuracy required in the machining and bending/forming processes makes my head hurt. Kudos to Leatherman.
-
@neillcurrie said:
I'd realized this before, but seeing the Wave disassembled just drives home how complex and difficult to manufacture the handles of the Wave are. Just imagining the accuracy required in the machining and bending/forming processes makes my head hurt. Kudos to Leatherman.Agree. I actually saw them being made in one of the older videos. The press cuts out a pre-formed single piece of die from the metal sheet, punches the holes and bends the blade locks, then another press presses the die into a "M" (or "W") shape while the bottom tools lock is inserted in it place. Simple as that. The whole process takes under 5 seconds. :o
However, getting the punches and presses to do what they're supposed to do to produce a finished Wave handle is another matter altogether ;)
-
This is gonna be awesome! Any reason you use a dryer instead of a smaller tumbler? Do you just not have one or does it have a different result?
-
@NKlamerus said:
This is gonna be awesome! Any reason you use a dryer instead of a smaller tumbler? Do you just not have one or does it have a different result?Standard method for someone who doesn't own dedicated tumbler. The canister goes into the dryer, works a charm ;)
More details below.
-
Stage 2, stone-wash done.
I did this in 3 turns, separating the small parts from the handles. First it was all the fasteners and handle stops. Secondly, it was one handle, than another.
My method involves a medium sized plastic container filled with small-to-medium sized pebbles. I first tumble the content by hand for first 5 minutes then check if this will produce a desired result. Then it goes for 20 minutes into the clothes dryer, wrapped into a large spare towel. Then last touch is applied by hand again for about 5 minutes.
The result is shown below, and I'm really stoked how well it came out. :)
Post tumbling color shown here is a tad darker than in real life.

I will try putting it all together either later today or tomorrow.
-
That turned out awesome.

-

So I just send you my Wave? Or is there some other method?
I am guessing this is for someone else since all you own are Surge's?

Good looking job by the way.
-
So I just send you my Wave? Or is there some other method?
I am guessing this is for someone else since all you own are Surge's?

Good looking job by the way.
Haha, thanks. I do own number of modded Waves too, not just Surges ;)
-
Here's all the bits lined up together, awaiting assembly.
Well, all except the scissors, they are shown by mistake as I will be swapping them with an awl.

Although it doesn't show well on the photo I polished a living daylight out of those spacers and washers, they're very smooth now.
-

You could switch out the small driver for the awl also right?
I see you got the Rebar head too.

-
You could switch out the small driver for the awl also right?
I see you got the Rebar head too.

Sure you can, they're the same size. However I find myself using small 2-way driver more often than scissors. 8)
-

You could switch out the small driver for the awl also right?
I see you got the Rebar head too.

Sure you can, they're the same size. However I find myself using small 2-way driver more often than scissors. 8)
Right.
I was just wondering because I am planning my Wave mods.
You ever do work for other people?
-

You could switch out the small driver for the awl also right?
I see you got the Rebar head too.

Sure you can, they're the same size. However I find myself using small 2-way driver more often than scissors. 8)
Right.
I was just wondering because I am planning my Wave mods.
You ever do work for other people?
Unless you're Downunder the whole excersize becomes cost prohibitive. Ancient NZ postal practices (read: exorbitant eye gouging on registered/courier International shipping cost) kill all the fun. :(
-
looks awesome so far.

-
Finished product! :ahhh
Please meet 'Acid Wave'




-
Nice job !
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login