A very unlikely shootout
-
So I did a head to head comparison of three tools that have never even slightly been considered competitiors! Why? I could say because I can and I was bored and couldn't think of anything better to do, but instead I'm going to tell you it's valuable research in cross-class comparison! The Gerber Dime- a diminutive keychain tool, the Gerber Crucial- a stripped down minimalist offering, and the Schrade Tough Tool- a full-sized brute with tons of tools. Not consumer advice, but the results were pretty interesting and it shows that you really shouldn't judge a book by its cover, or maybe a tool by the size of it's implements? Anyways, here's sidebyside testing of a Keychain, light duty mid-size, and full-size MT. Please feel free to comment and let me know what you think. This is in no way a comprehensive, or even good, test. Just a quick examination of how the tools each handle a few small tests.
Testing:
I decided only to test the implements that all three contenders had in common. This gave us both philips and flat drivers, blade, pliers, and wire cutters. Not a huge set of tests to run, but it is what it is, I think you guys can handle the let down.

First to be tested was the drivers. Three screws, a small combo head, then a thick flathead, and finally a philips head drywall screw were all driven(or attempted to be driven) into a solid block of hardwood.
Dime first.

Not outstanding, this is as deep as I would go for fear of snapping the little tool.Now Crucial.

Sunk it almost completely, but also stripped the screw quite a bit, not good.Schrade.

The crudely reground philips seated perfectly and was able to torque the head off without slipping once.Win- Schrade
Now the flathead, this screw required pre-drilling to get it to sink in any acceptable time even with a regular screwdriver.
Dime.

Almost completely flush! Yeah, I don't understand that one either.Crucial.

Decently far, but once again the head is quite mangled.Schrade.

Only had one of these screws, the Crucial beat it up a bit too much to get a solid purchase.Win- Dime?
Drywall Screw
Dime.

Set very smooth and very fast. But any more turning and something was likely to break.Crucial.

Fantastic! Honestly not far off from the time taken for a regular screwdriver, no slipping.Schrade.

Worse than the Dime. The ugly, messed up driver just wouldn't seat in this screw. My fault.Win- Crucial
Next was testing the blades, first on Nylon strap, then on paper.
Dime.

Two strokes to completely cut, not too bad. Tool didn't have factory edge to start test.Crucial.

Also two strokes, but just because it didn't cleanly cut where I started the stroke. Very clean cut.Schrade.

Four strokes, not overly clean. She's old, tired, and missing the tip so not too shocking.Win-Crucial
Paper Cutting
Dime.

Easy and smooth. Pushed through the cut rather hard and didn't really hang up.Crucial.

Not good, fat blade with a wide grind mixed with half serrations and what looks like a slight dent? in the blade.Schrade.

Similar to the Dime, but didn't feel as smooth and effortless.Win-Dime
Next test was a rather easy test for the wire cutters, light gauge single strand wire.

Dime.

Snipped it fairly easily, though resistance was felt and some force was needed.Crucial.

Surprised me, I expected the anvil cutters to sort of mash the wire, but just the weight of the handle swinging closed clipped the wire with ease.Schrade.

No problem, but not as effortless as the crucial. The cutters are beat up, but can easily handle more than this.Win-Crucial
The final test in my very un-comprehensive shootout was using the pliers to loosen an 11/32 bolt that had been tightened with a small ratchet.

Dime.

These pliers are basically advanced tweezers, but the slim profile let the meat of the gripping area get around the bolt and get it loose.Crucial.

Like the Dime, thin profile let the meat get on the bolt and get a solid purchase.Schrade.

Got it loose with just the tips, too fat to get the real part to grip, but definitely the best pliers in the test.Win-Crucial, because they're slim(But the Schrade pliers are hands-down better)
Closing thoughts:
Dime: Honestly I had previously perceived the drivers to be toy-like. The Flat driver is thinner than the average putty knife so I never would have thought it to be a genuinely useful tool, same goes for the pretend phillips head which got the drywall screw set so easily. But due to the tools size, setting is about all I would do with this tool, though that's to be expected. The blade is good for just about every EDC task I normally come across and it's shape gives it good belly for its tiny size. The pliers had just about met their match with the bolt, but who really expects keychain pliers to turn bolts. All in all, punched a bit above it's weight-class
Crucial: The middle didn't offer up the best of both worlds. The drivers left quite a bit to be desired, ruining two of three screws, oddly though it was the winner by a long shot on the final screw? Blade is certainly a beast to behold, but too much of it is serrated and there looks to be a small uneven spot in the part that actually is fine edged so it didn't cut paper well. It gives me the feeling of a rather cheap steel, though we'll likely never know for sure. So don't expect it to hold too long. The pliers are way too thin, that being said, they definitely gave the most sure-footed grip on the bolt and didn't even begin to slip. Also, the anvil cutters performed far better than I expected. All in all, performed adequately.
Schrade: The old girl is tired and worn, and it really shows. The philips driver tip had been completely snapped off the the previous owner, so I tried my best to make a new one with a dremel. This showed in the fact that it simply could not seat in the drywall screw(which I assume is a ph#2) The flat head was really wide, yet came to an exceptionally thin tip. This wasn't a good thing and led to it really struggling to grip after the Crucial had torn the head up a bit. The blade is chisel ground, which sucks, so I made it slightly less chisel ground and it has a decent working edge on it. But due to its grind I haven't been able to get a really good edge on it, so it performed averagely. Once again the previous owner broke the tip off that too, so no piercing is going to be happening. The ST1's pliers are my favorite MT pliers to use so far, though the task in testing was too narrow for anything but the tips, they still had no problem holding on and the added leverage made it a non-issue. The cutters lack a hard-wire notch, which strikes me as odd, but they had no problem with the little single strand wire despite not being as sharp as they may have been before. All in all, it's worn out but still has plenty of kick left.
Like always, please feel free to comment.
-
Nice review.

-
Thanks for the write-up.
This combination of tools makes you rethink were the boundaries are in different sized tools. I mean the Dime managed to win in some disciplines proofing that size is not everything. -
Nicely done, I like it.
-
Thank you guys, that was what jumped out at me as well. There are Certainly jobs that it would be foolish to try with a tool that wasn't the right size, but for most jobs it wouldn't hurt to try with what you have before running to get a "better" tool. Granted I would rather do foolish things like that with my Dime than a discontinued Squirt or something, but it reiterated the point that first and foremost these are tools.
I'm here more for general interest in MTs than I am because of how hard I use them. But this makes me want to just say smurf it and see what they can do. And that is the point of these things, so I'm glad I did this. plus the write up was fun.
-
Nice, interesting comparison Kyle-good work

-
Really interesting, thank you!

-
Thank you guys!
-
Great write up man! I think this type of comparison/review is great as it allows readers to see how different sized tools handle different tasks. One might think they need a full size, where a medium or even small one will do.

-
@derekmac said:
Great write up man! I think this type of comparison/review is great as it allows readers to see how different sized tools handle different tasks. One might think they need a full size, where a medium or even small one will do.
That hit me a bit to be honest, especially when the mid size couldn't handle a difficult task, but the small one can. That still has me scratching my head a bit. Honestly I'll probably do a few more tests in the coming weeks just for my own amusement. It's fun getting to see how well these tools really work.
It's no use carrying the Damn things around if you don't know what they can do or how to use them most effectively.
-
Great review mate
my dime hasnt seen much action since getting it in November,but looks like it will be usefull
mine was and still is very gritty? Is this normal on the dime 
-
@Zed said:
Great review mate
my dime hasnt seen much action since getting it in November,but looks like it will be usefull
mine was and still is very gritty? Is this normal on the dime 
What part of yours is gritty? I wouldn't call the action on mine flawless, but it isn't overly rough. When opening the tool from fully closed the scales rub together pretty solidly. This makes it feel like it's a rough pivot, but it's not the pivot it's Gerber not giving clearance for them to pass each other. I'm not sure if that's what you mean?
-
great comparison and shocking result.
-
Great review mate
my dime hasnt seen much action since getting it in November,but looks like it will be usefull
mine was and still is very gritty? Is this normal on the dime 
What part of yours is gritty? I wouldn't call the action on mine flawless, but it isn't overly rough. When opening the tool from fully closed the scales rub together pretty solidly. This makes it feel like it's a rough pivot, but it's not the pivot it's Gerber not giving clearance for them to pass each other. I'm not sure if that's what you mean?
when i squeeze the scales it sounds gritty as does the package opener,all work ok though,guess just needs a good wash out

-
Very nice write up.

-
Excellent review. Was kinda suprised how much they tore up the screws and seeing how that is the second most used part of my MTs that is not bueno.
Now do it again with tools that don't suck.

One of my Soldiers has a Crucial though and he loves it. Says the size is his favorite thing about it.
-
@HarleyXJGuy said:
Excellent review. Was kinda suprised how much they tore up the screws and seeing how that is the second most used part of my MTs that is not bueno.Now do it again with tools that don't suck.

One of my Soldiers has a Crucial though and he loves it. Says the size is his favorite thing about it.
You're too much
, I'll make sure I toss the X-Tract into the next review for you too. But there is likely to be another head to head soon, MP600 vs. Sidekick vs. Fuse maybe? But I find that odd that one of your boys is carrying one, do you know if he uses it often? Yea, I was a bit pissed at how quick the Crucial wrecked the screws, the flathead really is some foolish in-between size that doesn't seem to want to work at all. -
Excellent review. Was kinda suprised how much they tore up the screws and seeing how that is the second most used part of my MTs that is not bueno.
Now do it again with tools that don't suck.

One of my Soldiers has a Crucial though and he loves it. Says the size is his favorite thing about it.
You're too much
, I'll make sure I toss the X-Tract into the next review for you too. But there is likely to be another head to head soon, MP600 vs. Sidekick vs. Fuse maybe? But I find that odd that one of your boys is carrying one, do you know if he uses it often? Yea, I was a bit pissed at how quick the Crucial wrecked the screws, the flathead really is some foolish in-between size that doesn't seem to want to work at all.I have never seen him use his Crucial. Will ask next tiime I see him.
You should toss a LLST into a comparo.
I will give 2 to 1 on the MP 600 for the next review.

-
Excellent review. Was kinda suprised how much they tore up the screws and seeing how that is the second most used part of my MTs that is not bueno.
Now do it again with tools that don't suck.

One of my Soldiers has a Crucial though and he loves it. Says the size is his favorite thing about it.
You're too much
, I'll make sure I toss the X-Tract into the next review for you too. But there is likely to be another head to head soon, MP600 vs. Sidekick vs. Fuse maybe? But I find that odd that one of your boys is carrying one, do you know if he uses it often? Yea, I was a bit pissed at how quick the Crucial wrecked the screws, the flathead really is some foolish in-between size that doesn't seem to want to work at all.I have never seen him use his Crucial. Will ask next tiime I see him.
You should toss a LLST into a comparo.
I will give 2 to 1 on the MP 600 for the next review.

You're betting on the MP to win it? Dam I'll take that bet in a heartbeat! Want to lay all your shiny new SAKs on the line???
Just kidding.I will never own a LLST, nor should any other sound minded individual! But I'd be glad to hear what he has to say, I'll likely carry the Crucial a bit. Not a terrible tool, just certainly not the best one I own...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login