Leatherman QC Fails
-
I just got a new Rebar yesterday and it has none of the problems mentioned here, the pliers don't lock up like BigMatt's, the tools aren't loose and the little spring inside isn't loose. However, when closed the halves don't line up very well, they're about 1/8" off.
Every single Juice I've owned, and I've owned about 5, have had the same problem with the halves not lining up when closed. I sent the first Juice back after another problem with it occurred and they sent me a replacement that didn't line up either, so since then I haven't bothered.
Yea, it would be nice to see Vic QC come to Leatherman, or at least a step in that direction.
That being said, I really like the Rebar.
-
@3rdpig said:
I just got a new Rebar yesterday and it has none of the problems mentioned here, the pliers don't lock up like BigMatt's, the tools aren't loose and the little spring inside isn't loose. However, when closed the halves don't line up very well, they're about 1/8" off.Every single Juice I've owned, and I've owned about 5, have had the same problem with the halves not lining up when closed. I sent the first Juice back after another problem with it occurred and they sent me a replacement that didn't line up either, so since then I haven't bothered.
Yea, it would be nice to see Vic QC come to Leatherman, or at least a step in that direction.
That being said, I really like the Rebar.
For Juices, only the Kf4 has symmetrically thick halves; all other models have different thicknesses to the sides, which might make it appear not lined up.
-
For Juices, only the Kf4 has symmetrically thick halves; all other models have different thicknesses to the sides, which might make it appear not lined up.
I believe the xe6 is even too, but the corkscrew makes it feel uneven.
... I can't remember as it's been a while since I let my XE6 go, but the CS4 if definitely uneven, and I thought the file and serrated blade was the same thickness, which would mean the XE6 has the same offset, This is unless they compensated for it at the factory, in which case why not do it with them all? -
@50ft-trad said:
For Juices, only the Kf4 has symmetrically thick halves; all other models have different thicknesses to the sides, which might make it appear not lined up.
I believe the xe6 is even too, but the corkscrew makes it feel uneven.
... I can't remember as it's been a while since I let my XE6 go, but the CS4 if definitely uneven, and I thought the file and serrated blade was the same thickness, which would mean the XE6 has the same offset, This is unless they compensated for it at the factory, in which case why not do it with them all?It's all about the awl or the can opener, that offsets the handles. Drives me nuts.
I'll never use a 'factory' Juice again...ahem.

-
@Sazabi said:
For Juices, only the Kf4 has symmetrically thick halves; all other models have different thicknesses to the sides, which might make it appear not lined up.True, and I can live with that, but even then you'd think they'd halfway line up, either one side of each half, or the smaller half sitting in the middle of the bigger one. But it's never like that. But it's not a big deal, specially on the Juice.
The Rebar shouldn't be this far off though. But I'm willing to live with it since it's otherwise perfect.
I'm betting it's a simple matter of loosening the nuts on the pliers end, repositioning the handles and then tightening the nuts back up. Simple that is if I had a tool to fit the knurled nuts, or was willing to go out to the garage on a 110 degree day and make one. But I don't and I won't. :-[
-
Rise old thread! RISE!!
Ok, my file won't lock in on my wave. On closer inspection, the bump on the outside of the liner lock is half worn off from about 2 days of use from when I first got the wave new. Not only that, but the small hole in the file that the ball fits into to keep it locked in is far to small to fit the ball, so my file will open up whenever my wave is moved fast enough. Now I'm assuming the design of the hole and the ball are intentionally like that, but i cannot see how that is supposed to work, and the ball was pretty much ground like it is now from when i opened the box. the pictures are taken at pretty much the same distance so it should give you an idea of how much smaller the hole is. -
Surge blade play
Ps4 sloppy tools -
@bounding star said:
Rise old thread! RISE!!
Ok, my file won't lock in on my wave. On closer inspection, the bump on the outside of the liner lock is half worn off from about 2 days of use from when I first got the wave new. Not only that, but the small hole in the file that the ball fits into to keep it locked in is far to small to fit the ball, so my file will open up whenever my wave is moved fast enough. Now I'm assuming the design of the hole and the ball are intentionally like that, but i cannot see how that is supposed to work, and the ball was pretty much ground like it is now from when i opened the box. the pictures are taken at pretty much the same distance so it should give you an idea of how much smaller the hole is.This problem is exactly why the Wave and I never got along well.
-
@bounding star said:
Rise old thread! RISE!!
Ok, my file won't lock in on my wave. On closer inspection, the bump on the outside of the liner lock is half worn off from about 2 days of use from when I first got the wave new. Not only that, but the small hole in the file that the ball fits into to keep it locked in is far to small to fit the ball, so my file will open up whenever my wave is moved fast enough. Now I'm assuming the design of the hole and the ball are intentionally like that, but i cannot see how that is supposed to work, and the ball was pretty much ground like it is now from when i opened the box. the pictures are taken at pretty much the same distance so it should give you an idea of how much smaller the hole is.Both the file and saw on my Wave have similarly "small" depressions compared with the bump OD. The saw is retained closed, my file is now reversed in a knife slot. Can't say I noticed a retention issue NIB. I have a LM opener tool in the other knife slot. I ground a depression of a similar OD to the bump and it closes with quite a satisfying click and the liner lock sits flush with the tool face. Planning on grinding larger depressions all round when some tooling arrives.
I'm baffled whether the small depressions are by design or a QC fail.
-
I was studying my Wave bit changer while considering this post...
</topic/57011
I have added a 3D Phillips to my Wave but retained the bit changer and normally have the #0/#3 bit from the Bit Adapter kit installed.
http://www.leatherman.com/931012.html
I noticed the spring was not engaging the bit with #0 deployed (OK the other way). Then I noticed some weirdness at the #3 end. Can't be intended as not shown on the LM pic. If I'd noticed this on receipt I'd have returned it to Amazon.
-
Just got a new Style CS, the nice little holes in the blade were missing. Not a real problem, but i liked those holes...

-
assuming that this was an one-off and they have not just changed the way they make the blades it may be of interest to collectors.
-
@bounding star said:
Just got a new Style CS, the nice little holes in the blade were missing. Not a real problem, but i liked those holes...

Could you please post a pic that shows the nail nick side of the blade.
Yup, interested to see it too. You tried to link to your dropbox, but as the picture isn't in your public folder we can't see it without your password. ;) Try moving it to the public folder or using Photobucket or attaching the picture to your post in the reply window +Attachments and other options
-
Totally did not notice that when I quoted it.

-
Sorry bout that, does this work?

-
Yes, it does.

Looks like they installed a Squirt blade into yours. The Style blade also has a bit of a bump on the back of the blade and the nail nick is lower.
-
and this one too apparently?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login