Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Leatherman weak points

Scheduled Pinned Locked Moved Leatherman Tools
31 Posts 1 Posters 8.5k Views
  1. Home
  2. Tool Talk
  3. Leatherman Tools
  4. Leatherman weak points
Leatherman weak points
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • WhichDawg Offline
    WhichDawg
    Posts: 7,559
    WhichDawg Offline
    WhichDawg
    wrote on last edited by
    #2 Quote Reply

      my biggest problem is spotting rust. it does come off easy enough but I wonder if I left it what will happen.
      I've been reading more and more about the pin issue and it's a concern.

      my second issue is the plastic they put in some models, whether it's for lightness, cheaper cost or other I
      worry about plastic in tools/parts over the long haul because in the past it becomes brittle and fragile.

      thx for your experience and comments. I think no tool is perfect because their are cons and pros with
      everyone but I still feel Leathermans are great tools (I still want them all!).

      1 Reply Last reply
      • Leatherman123 Offline
        Leatherman123
        Posts: 6,568
        Leatherman123 Offline
        Leatherman123
        wrote on last edited by
        #3 Quote Reply

          I have broken a few locking tabs before as well..

          1 Reply Last reply
          • Smitty44 Offline
            Smitty44
            Posts: 2,026
            Smitty44 Offline
            Smitty44
            wrote on last edited by Smitty44
            #4 Quote Reply

              Welcome to the forums kwakster,where is it that you work?That you see so all of those problems,and I agree with all the problems that you pointed out,we need to get you into an engineer job!!!

              1 Reply Last reply
              • Mike, Lord of the Spammers! Offline
                Mike, Lord of the Spammers!
                Posts: 42,975
                Mike, Lord of the Spammers! Offline
                Mike, Lord of the Spammers!
                wrote on last edited by
                #5 Quote Reply

                  Thanks for such an honest and thought provoking critique :)

                  I can understand LM's reluctance to adopt new steel's for the plier head, but the other fault's really should be addressed :-\

                  1 Reply Last reply
                  • Leatherman123 Offline
                    Leatherman123
                    Posts: 6,568
                    Leatherman123 Offline
                    Leatherman123
                    wrote on last edited by
                    #6 Quote Reply

                      I completely agree with you, Mike.. But, why doesn't Victorinox fix the simple flaws on their SwissTools? By this I mean: square off the drivers, make the lock up solid ( like on Spirit), and make the philips driver out of harder steel! Or, why doesn't SOG have a chisel grind on their MT knives? They are a knife company after all, right? Or, why doesn't Gerber make longer screwdrivers? You get what I'm saying?

                      1 Reply Last reply
                      • max6166 Offline
                        max6166
                        Posts: 1,547
                        max6166 Offline
                        max6166
                        wrote on last edited by
                        #7 Quote Reply

                          Yeah, why don't they? I am sure there is a reason for how slow companies are to change and address these sorts of issues. I only have some uneducated guesses. I wonder what what their reasoning really is... ???

                          The SwissTool is an oddball though. You can see that Vic have been fiddling with the SwissTool plier heads every few years, but not with anything else as far as I know...

                          1 Reply Last reply
                          • Leatherman123 Offline
                            Leatherman123
                            Posts: 6,568
                            Leatherman123 Offline
                            Leatherman123
                            wrote on last edited by
                            #8 Quote Reply

                              They only other changes I know of is- that the wire stripper cut out is not as deep.. I may be wrong, but I remember Dunc posting about this..

                              1 Reply Last reply
                              • Mike D Offline
                                Mike D
                                Posts: 169
                                Mike D Offline
                                Mike D
                                wrote on last edited by
                                #9 Quote Reply

                                  What I want to know Kwakster is do you repair multi"s like professionally?

                                  I have two Swisstools that need fixed...

                                  1 Reply Last reply
                                  • jdailey4206966 Offline
                                    jdailey4206966
                                    Posts: 270
                                    jdailey4206966 Offline
                                    jdailey4206966
                                    wrote on last edited by
                                    #10 Quote Reply

                                      @max6166 said:
                                      Yeah, why don't they? I am sure there is a reason for how slow companies are to change and address these sorts of issues. I only have some uneducated guesses. I wonder what what their reasoning really is... ???

                                      The SwissTool is an oddball though. You can see that Vic have been fiddling with the SwissTool plier heads every few years, but not with anything else as far as I know...

                                      It's ANTICIPATION........meaning they will leave you wondering, "wow, will this be the "perfect" tool with everything squared, and longer tools, and just everything perfect with a guarantee never to break?"

                                      Please let me know if you come across that tool.....

                                      1 Reply Last reply
                                      • ultimaonliner Offline
                                        ultimaonliner
                                        Posts: 329
                                        ultimaonliner Offline
                                        ultimaonliner
                                        wrote on last edited by
                                        #11 Quote Reply

                                          Life's sick comedy.

                                          1 Reply Last reply
                                          • kwakster Offline
                                            kwakster
                                            Posts: 1,006
                                            kwakster Offline
                                            kwakster
                                            wrote on last edited by
                                            #12 Quote Reply

                                              @Mike D said:
                                              What I want to know Kwakster is do you repair multi"s like professionally?

                                              I have two Swisstools that need fixed...

                                              Yes, you can say that.
                                              Although i'm mainly a content editor, someone who writes productinfo and background information on websites, repairing mostly Leatherman multitools and Buck knives, as well as sharpening are part of my daily routine.
                                              But i only work three days a week, :D

                                              But sorry, the company i work for doesn't carry Victorinox, only Wenger.
                                              I know that Victorinox owns Wenger, but where i live the two are strictly separated.

                                              1 Reply Last reply
                                              • AndyTiedye Offline
                                                AndyTiedye
                                                Posts: 1,225
                                                AndyTiedye Offline
                                                AndyTiedye
                                                wrote on last edited by
                                                #13 Quote Reply

                                                  @Mike D said:
                                                  What I want to know Kwakster is do you repair multi"s like professionally?

                                                  I have two Swisstools that need fixed...

                                                  How did you manage to break them? They seem really solid.

                                                  1 Reply Last reply
                                                  • J-sews Offline
                                                    J-sews
                                                    Admin Team
                                                    Posts: 23,224
                                                    J-sews Offline
                                                    J-sews
                                                    Admin Team
                                                    wrote on last edited by
                                                    #14 Quote Reply

                                                      @kwakster said:
                                                      Biggest problem i encounter are always the locking tabs.
                                                      When exerting pressure on one of the smaller items, all the force gets transferred onto 2 tiny metal pins which cannot handle this very well and shear off.

                                                      kwakster, which Leatherman model are you referring to?

                                                      On the Fuse, Blast, Core, Wave, Charge, Surge, etc, there are metal tabs on the lock bar which fit into slots. (circled) I would have thought this arrangement would take the load completely off the two pins?? ???

                                                      1 Reply Last reply
                                                      • kwakster Offline
                                                        kwakster
                                                        Posts: 1,006
                                                        kwakster Offline
                                                        kwakster
                                                        wrote on last edited by
                                                        #15 Quote Reply

                                                          @J-sews said:

                                                          @kwakster said:

                                                          Biggest problem i encounter are always the locking tabs.
                                                          When exerting pressure on one of the smaller items, all the force gets transferred onto 2 tiny metal pins which cannot handle this very well and shear off.

                                                          kwakster, which Leatherman model are you referring to?

                                                          On the Fuse, Blast, Core, Wave, Charge, Surge, etc, there are metal tabs on the lock bar which fit into slots. (circled) I would have thought this arrangement would take the load completely off the two pins?? ???

                                                          I see this problem occuring on all models with locking tabs, but mostly on Wave's, Charges, and Blasts while we sell those models the most.
                                                          The lockbar that fits into the slots needs just a little room to function properly, meaning it hasn't got a supertight fit into it's slot.
                                                          And this is just enough to transfer the forces excerted mainly on the screwdrivers onto the small pins or hinges, which obviously cannot handle this stress very well.

                                                          1 Reply Last reply
                                                          • J-sews Offline
                                                            J-sews
                                                            Admin Team
                                                            Posts: 23,224
                                                            J-sews Offline
                                                            J-sews
                                                            Admin Team
                                                            wrote on last edited by
                                                            #16 Quote Reply

                                                              Very interesting. I would not have guessed this area was a weakness. :-\

                                                              @kwakster said:
                                                              Third biggest problem is the tiny metal pin that helps to keep the plierhead seated when closed.
                                                              This pin bends and breaks easily, at which point the tool doesn't close easily anymore, you will have to guide the plierhead by hand.
                                                              My solution to this is as follows.
                                                              Just in front of the little pin is a rivet which is cut off short to make room for the plierhead.
                                                              If a longer rivet was used the plierhead could rest upon it and the weak metal pin could be left out.

                                                              ...and on this point I'm assuming you refer to the pin circled below? It does indeed seem like a fragile part. (although I've never had one break)

                                                              How do you repair tools that come to you with this pin broken? ???

                                                              1 Reply Last reply
                                                              • kwakster Offline
                                                                kwakster
                                                                Posts: 1,006
                                                                kwakster Offline
                                                                kwakster
                                                                wrote on last edited by kwakster
                                                                #17 Quote Reply

                                                                  @J-sews said:
                                                                  Very interesting. I would not have guessed this area was a weakness. :-\

                                                                  @kwakster said:

                                                                  Third biggest problem is the tiny metal pin that helps to keep the plierhead seated when closed.
                                                                  This pin bends and breaks easily, at which point the tool doesn't close easily anymore, you will have to guide the plierhead by hand.
                                                                  My solution to this is as follows.
                                                                  Just in front of the little pin is a rivet which is cut off short to make room for the plierhead.
                                                                  If a longer rivet was used the plierhead could rest upon it and the weak metal pin could be left out.

                                                                  ...and on this point I'm assuming you refer to the pin circled below? It does indeed seem like a fragile part. (although I've never had one break)

                                                                  How do you repair tools that come to you with this pin broken? ???

                                                                  Yep, that is the pin i was talking about.
                                                                  Most of the time it starts to bend outwards first, and breaks off when people try to bend it back.
                                                                  When i get one of these back in shop i have to replace the whole leg, and build all the items back into it.

                                                                  In your picture you can also see the rivet i was talking about, just right from the pin.
                                                                  If Leatherman would just leave it longer, instead of cutting it short, it would be a whole lot stronger than that weak little pin.

                                                                  1 Reply Last reply
                                                                  • MultiMat Offline
                                                                    MultiMat
                                                                    Posts: 8,694
                                                                    MultiMat Offline
                                                                    MultiMat
                                                                    wrote on last edited by
                                                                    #18 Quote Reply

                                                                      Kwakster while we are asking ::) ::) ::) What tool do you use to remove LM's knurled fasteners ? And how do I get them :pok: . Does it involve "Black ops" , 007 & a magic wand ? I can not bring myself to creating a set of spoony's customized sockets ( hammering the knurl impression into a cheap socket). :cheers:

                                                                      1 Reply Last reply
                                                                      • kwakster Offline
                                                                        kwakster
                                                                        Posts: 1,006
                                                                        kwakster Offline
                                                                        kwakster
                                                                        wrote on last edited by
                                                                        #19 Quote Reply

                                                                          @MultiMat said:
                                                                          Kwakster while we are asking ::) ::) ::) What tool do you use to remove LM's knurled fasteners ? And how do I get them :pok: . Does it involve "Black ops" , 007 & a magic wand ? I can not bring myself to creating a set of spoony's customized sockets ( hammering the knurl impression into a cheap socket). :cheers:

                                                                          There are some flat pieces of steel with holes exactly forming the outline of specific knurled fasteners, and next to these i also have several specialized sockets to put on a screwdriver fitted with a square tip.
                                                                          While i'm not familiar with all the right names for these kind of tools, i think you know what i mean,

                                                                          I will try to make some pictures of these in a few days.
                                                                          On the sockets are American brand names that i'm not familiar with, but maybe you can get them where you live.

                                                                          1 Reply Last reply
                                                                          • jdailey4206966 Offline
                                                                            jdailey4206966
                                                                            Posts: 270
                                                                            jdailey4206966 Offline
                                                                            jdailey4206966
                                                                            wrote on last edited by
                                                                            #20 Quote Reply

                                                                              @kwakster said:

                                                                              @J-sews said:

                                                                              Very interesting. I would not have guessed this area was a weakness. :-\

                                                                              @kwakster said:

                                                                              Third biggest problem is the tiny metal pin that helps to keep the plierhead seated when closed.
                                                                              This pin bends and breaks easily, at which point the tool doesn't close easily anymore, you will have to guide the plierhead by hand.
                                                                              My solution to this is as follows.
                                                                              Just in front of the little pin is a rivet which is cut off short to make room for the plierhead.
                                                                              If a longer rivet was used the plierhead could rest upon it and the weak metal pin could be left out.

                                                                              ...and on this point I'm assuming you refer to the pin circled below? It does indeed seem like a fragile part. (although I've never had one break)

                                                                              How do you repair tools that come to you with this pin broken? ???

                                                                              Yep, that is the pin i was talking about.
                                                                              Most of the time it starts to bend outwards first, and breaks off when people try to bend it back.
                                                                              When i get one of these back in shop i have to replace the whole leg, and build all the items back into it.

                                                                              In your picture you can also see the rivet i was talking about, just right from the pin.
                                                                              If Leatherman would just leave it longer, instead of cutting it short, it would be a whole lot stronger than that weak little pin.

                                                                              I don't know about weak??? Have you ever tried to cut one on those pins? I used to work at a place where we used the same type of metal pins and the only way to snap them was to use lineman pliers in a vice. It is a tough metal, but I suppose could give after some time, but it would have to be a long time. Also the pin inside for the plier head has never given me any problems. I have worked my Wave like a balisong before and never gave me any trouble, but I know that if anything should ever happen that LM will fix it under the 25 yr warranty :D

                                                                              1 Reply Last reply
                                                                              • MultiMat Offline
                                                                                MultiMat
                                                                                Posts: 8,694
                                                                                MultiMat Offline
                                                                                MultiMat
                                                                                wrote on last edited by
                                                                                #21 Quote Reply

                                                                                  @kwakster said:

                                                                                  @MultiMat said:

                                                                                  Kwakster while we are asking ::) ::) ::) What tool do you use to remove LM's knurled fasteners ? And how do I get them :pok: . Does it involve "Black ops" , 007 & a magic wand ? I can not bring myself to creating a set of spoony's customized sockets ( hammering the knurl impression into a cheap socket). :cheers:

                                                                                  There are some flat pieces of steel with holes exactly forming the outline of specific knurled fasteners, and next to these i also have several specialized sockets to put on a screwdriver fitted with a square tip.
                                                                                  While i'm not familiar with all the right names for these kind of tools, i think you know what i mean,

                                                                                  I will try to make some pictures of these in a few days.
                                                                                  On the sockets are American brand names that i'm not familiar with, but maybe you can get them where you live.

                                                                                  I live in Australia so it might be a stretch but the internet has made the world so well connected. Photos & names of those special tools :drool: :drool: :gimme: :gimme: Please :D

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. Leatherman Tools
                                                                                  4. Leatherman weak points
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0